D8B Manual • Appendices • page 174
D8B
Button
Number
D8B Button
Mapped HUI Button
Global
Mode
General HUI Layer
Comments
DP3.1 Function
Fader 17-24
Fader 1-8
N
Channel V-Pot
17-24
Channel V-Pot 1-8
N
Mute 17-24
Mute 1-8
N
Solo 17-24
Solo 1-8
N
Select 17-24
Select 1-8
N
Record Ready
17-24
Record Ready 1-8
N
Assign 17-24
VSel 1-8
N
Alt+Assign 17-
24
Insert 1-8
N
Write 17-24
Auto 1-8
N
1
Level to Tape
Aux Mute
N
2
Digital Trim
Shift (flip)
N
3
Aux 1
Send A
N
4
Aux 2
Send B
N
5
Aux 3
Send C
N
6
Aux 4
Send D
N
7
Aux 5
Send E
N
8
Aux 7
Rec Ready All
N
9
Aux 9-10
Bank Left
N
10
Aux 11-12
Bank Right
N
11
Aux 9-10 Pan
Channel Left
N
12
Aux 11-12 Pan
Channel Right
N
13
Pan
Pan
N
14
Shift
N
Shift + Masters
N/A
Y
Go to HUI Layer on
D8B
D8B VFD Display
N
D8B VFD V-Pots
N
Alt+Right D8B
VFD V-Pot
Scroll
N
D8B VFD Select
Buttons
N
Previous / Next
N/A
N
15
On
Assign
N
16
Setup
Compare
N
17
Memory A
Bypass
N
18
Memory B
Insert
N
19
EQ
Window Transport
N
20
Gate
Window ALT
N
21
Compressor
Window Edit
N
22
Plug-ins
Window Status
N
23
Load Patch
Window Mix
N
24
Save Patch
Window Mem Loc
N
25
Assign Bus 2
Auto Enable Send
N
26
Assign Bus 3
Auto Enable Plug-in
N
27
Assign Bus 4
Auto Enable Send
Mute
N
28
Assign Bus 5
Auto Mode Read
N
29
Assign Bus 7
Auto Mode Latch
N
30
Assign Bus 8
Auto Mode Write
N
31
Assign L-R
Shift/Add
N
32
Assign Route To
Tape
Save
N
33
Automation
Bypass
Auto Mode Off
N
34
Automation
Faders
Auto Enable Fader
N
Move corresponding DP3 channel Fader.
Move corresponding DP3 channel Pan or Send Level
Mute corresponding DP3 channel
Solo corresponding DP3 channel
Select corresponding DP3 channel
Record Arm corresponding DP3 channel
Toggle Pre/Post of corresponding PT channel Send for selected Aux 1-5. If Level To Tape (HUI Aux Mute) is lit,
then it will toggle the mute status of the corresponding PT channel send for the selected Aux 1-5.
Select corresponding DP3 channel for Insert Editing in VFD
Use in conjunction with Auto Mode values to set automation mode for corresponding DP3 Channel.
When lit, assign (V-Sel) toggles the mute status of the selected Aux. When not lit, V-Sel will toggle the selected Aux Pre/Post.
N/A
Enables control of DP3 Mixing Board Aux 1 by HUI layer V-Pots
Enables control of DP3 Mixing Board Aux 2 by HUI layer V-Pots
Enables control of DP3 Mixing Board Aux 3 by HUI layer V-Pots
Enables control of DP3 Mixing Board Aux 4 by HUI layer V-Pots
N/A
N/A
Shifts HUI layer to left by 8 to view previous 8 faders
Shifts HUI layer to right by 8 to view next 8 faders
Shifts HUI layer to left by 1 to view previous fader
Shifts HUI layer to right by 1 to view next fader
Enables control of VST channel settings Pan on HUI layer V-Pots
N/A
Go to HUI layer on D8B
Displays Plug-in/Insert settings for selected Insert Channel. There are two main views: Plug-in Edit View and Insert Assign view.
Changes the assigned Plug-in, chooses a Plug-in Preset, or adjusts a plug-in parameter listed in bottom line of VFD.
Scroll to next/previous parameter of plug-in parameters in Plug-in Edit View. Scroll to next/previous insert in Insert Assign View.
Select Insert Slot for Editing in Insert Assign View. Selected Insert has Arrows pointing to the Slot.
Change between normal HUI VFD mode and channel HUI VFD Mode. See note below.
Toggles function of VFD V-Pots in Insert Assign view. When not lit, V-Pots select Plug-in for their corresponding slot.
When lit, V-Pots select preset for their corresponding plug-in.
N/A
Toggles bypass of selected plug-in
Toggles Plug-in Edit Mode for selected plug-in
Bring to front Control Panel Window (Transport)
Open Insert Window
Open Sequence Editor Window
Open Audio Monitor Window
Open Mixing Board Window
Open Markers Window
Toggles Send Level Automation Enable in DP3 Automation Setup window
Toggles Effect Bypass and Effect Parameter Automation Enables in DP3 Automation Setup window
Toggles Send Mute Automation Enable in DP3 Automation Setup window
Hold and Press a channel Write (HUI Auto) button to enable automation playback on the corresponding DP3 channel
Hold and Press a channel Write (HUI Auto) button to enable automation playback and recording on the corresponding
DP3 channel, and to put the channel into Latch automation mode.
Hold and press a channel Write (HUI Auto) button to enable automation playback and recording on the corresponding
DP3 channel, and to put the channel into Overwrite automation mode.
Shifts to second function of some buttons. Used to select multiple values of some parameters.
Press twice to save the open DP3 session
Hold and press a channel Write (HUI Auto) button to disable automation playback and recording on the corresponding
DP3 channel, and to put the channel into Touch automation mode.
Toggles Audio Volume and MIDI Volume Automation Enables in DP3 Automation Setup window
Last Updated: 2/07/03
16220 Woodinville Redmond Rd. NE Woodinville, WA 98072
Tel: 800-258-6883 Fax: 425-806-6312 e-mail: techmail@mackie.com
D8B v5.1 B445 HUI Layer Control Mapping
For DP3.1
Summary of Contents for d8B V5.1
