background image

8

RIGGING

The FUSSION 1800SA and 1800S cabi-

nets are not designed for rigging or flying.
The cabinets are for floor-mounting only.

WARNING:

 Never attempt to suspend the

FUSSION 1800SA or 1800S loudspeakers
by their handles.

AC POWER

The FUSSION 1800SA is shipped with a

connector that mates with the AC recep-
tacle on the rear panel. Use heavy gauge
wire for the linecord to avoid power losses
across the wire.

The following guide should be followed

when wiring a linecord:

specified line voltage, the built-in amplifiers
will no longer be able to supply rated
power. (They will continue to operate
down to 80% of the rated line voltage, but
won’t reach full power, resulting in lower
headroom.)

Under maximum SPL conditions,

where musical peaks are just clipping, the
FUSSION 1800SA has the following cur-
rent requirements:

115V

230V

Max. Continuous RMS

10A

6A

Max. Peak

 12A

8A

Be sure the electrical service can supply

enough amperage for all the components
connected to it.

We recommend that a stiff (robust) sup-

ply of AC power be used because the
amplifiers place high current demands on
the AC line. The more power that is avail-
able on the line, the louder the speakers will
play and the more peak output power will
be available for cleaner, punchier bass. A
suspected problem of “poor bass perfor-
mance” is often caused by a weak AC
supply to the amplifiers.

Never remove the
ground pin on the power
cord of the FUSSION
1800SA or any other
component. This is very
dangerous.

North America

International

115VAC

   230VAC

Hot

Black

Blue

Neutral

White

Brown

Earth (Ground)

Green w/ 

Green

yellow stripe

NEUTRAL

WHITE (115V) OR 

BROWN (230V)

HOT 

BLACK (115V) OR 

BLUE (230V)

HOT 

BLACK (115V) OR 

BLUE (230V)

GROUND

GREEN 

W/YELLOW 

STRIPE (115V) 

or GREEN (230V)

20A. 250V

MALE

20A. 250V

FEMALE

GROUND

GREEN 

W/YELLOW 

STRIPE (115V) 

or GREEN (230V)

NEUTRAL

WHITE (115V) OR 

BROWN (230V)

AC Power Connectors

Be sure the FUSSION 1800SA is plugged

into an outlet that is able to supply the cor-
rect voltage specified for your model. If the
voltage should drop below 97% of the

Summary of Contents for FUSSION 1800S













Reviews: