background image

2

PPM608

PPM608

1.

  Read these instructions.  

2.

  Keep these instructions.

3.

  Heed all warnings.

4.

  Follow all instructions.

5.

  Do not use this apparatus near water.

6.

  Clean only with a dry cloth.

7.

  Do not block any ventilation openings. Install in accordance with the 

manufacturer’s instructions.

8.

  Do not install near any heat sources such as radiators, heat registers, 

stoves, or other apparatus (including amplifiers) that produce heat.

9.

  Do not defeat the safety purpose of the polarized or grounding-type 

plug. A polarized plug has two blades with one wider than the other. 

A grounding-type plug has two blades and a third grounding prong. 

The wide blade or the third prong are provided for your safety. If the 

provided plug does not fit into your outlet, consult an electrician for 

replacement of the obsolete outlet.

10.

 Protect the power cord from being walked on or pinched particularly at 

plugs, convenience receptacles, and the point where they exit from the 

apparatus.

11.

 Only use attachments/accessories specified by the manufacturer.

12.

 Use only with a cart, stand, tripod, bracket, or table 

specified by the manufacturer, or sold with the 

apparatus. When a cart is used, use caution when 

moving the cart/apparatus combination to avoid 

injury from tip-over.

13.

 Unplug this apparatus during lightning storms or 

when unused for long periods of time.

14.

 Refer all servicing to qualified service personnel. Servicing is required 

when the apparatus has been damaged in any way, such as power-

supply cord or plug is damaged, liquid has been spilled or objects have 

fallen into the apparatus, the apparatus has been exposed to rain or 

moisture, does not operate normally, or has been dropped.

15.

 Do not overload wall outlets and extension cords as this can result in a 

risk of fire or electric shock.

16.

 This apparatus shall not be exposed to dripping or splashing, and no 

object filled with liquids, such as vases or beer glasses, shall be placed 

on the apparatus.

17.

 This apparatus has been designed with Class-I construction and must 

be connected to a mains socket outlet with a protective earthing  

connection (the third grounding prong).

18.

 This apparatus has been equipped with an all-pole, rocker-style AC 

mains power switch. This switch is located on the rear panel and 

should remain readily accessible to the user.

19.

 NOTE: This equipment has been tested and found to comply with the 

limits for a Class B digital device, pursuant to part 15 of the FCC Rules. 

These limits are designed to provide reasonable protection against 

harmful interference in a residential installation. This  

equipment generates, uses, and can radiate radio frequency energy 

and, if not installed and used in accordance with the instructions, may 

cause harmful interference to radio communications. However, there is 

no guarantee that interference will not occur in a particular installation. 

If this equipment does cause harmful interference to radio or television 

reception, which can be determined by turning the equipment off and 

on, the user is encouraged to try to correct the interference by one or 

more of the following measures:

•  Reorient or relocate the receiving antenna.

•  Increase the separation between the equipment and the 

receiver.

•  Connect the equipment into an outlet on a circuit different from 

that to which the receiver is connected.

•  Consult the dealer or an experienced radio/TV technician for 

help.

  CAUTION: Changes or modifications to this device not expressly 

approved by LOUD Technologies Inc. could void the user's authority to 

operate the equipment under FCC rules.

20.

 This apparatus does not exceed the Class A/Class B (whichever is 

applicable) limits for radio noise emissions from digital apparatus as 

set out in the radio interference regulations of the Canadian Department 

of Communications.

ATTENTION

 — 

Le présent appareil numérique n’émet pas de bruits 

radioélectriques dépassant las limites applicables aux appareils 

numériques de class A/de class B (selon le cas) prescrites dans le 

réglement sur le brouillage radioélectrique édicté par les ministere des 

communications du Canada.

21.

 Exposure to extremely high noise levels may cause permanent hearing 

loss. Individuals vary considerably in susceptibility to noise-induced 

hearing loss, but nearly everyone will lose some hearing if exposed to 

sufficiently intense noise for a period of time. The U.S. Government’s 

Occupational Safety and Health Administration (OSHA) has specified 

the permissible noise level exposures shown in the following chart.

  According to OSHA, any exposure in excess of these permissible limits 

could result in some hearing loss. To ensure against potentially   

dangerous exposure to high sound pressure levels, it is recommended 

that all persons exposed to equipment capable of producing high 

sound pressure levels use hearing protectors while the equipment 

is in operation. Ear plugs or protectors in the ear canals or over the 

ears must be worn when operating the equipment in order to prevent 

permanent hearing loss if exposure is in excess of the limits set forth 

here:

Important Safety Instructions

CAUTION    AVIS

RISK OF ELECTRIC 

SHOCK. DO NOT OPEN

RISQUE DE CHOC ELECTRIQUE. NE PAS OUVRIR

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL

ATTENTION: POUR EVITER LES RISQUES DE CHOC ELECTRIQUE, NE PAS ENLEVER LE COUVERCLE. 

AUCUN ENTRETIEN DE PIECES INTERIEURES PAR L'USAGER. 

CONFIER L'ENTRETIEN AU PERSONNEL QUALIFIE.

AVIS: POUR EVITER LES RISQUES D'INCENDIE OU D'ELECTROCUTION, N'EXPOSEZ PAS CET ARTICLE 

A LA PLUIE OU A L'HUMIDITE

The lightning flash with arrowhead symbol within an equilateral triangle is 

intended to alert the user to the presence of uninsulated "dangerous 

voltage" within the product's enclosure, that may be of sufficient magnitude 

to constitute a risk of electric shock to persons.

Le symbole éclair avec point de flèche à l'intérieur d'un triangle équilatéral 

est utilisé pour alerter l'utilisateur de la présence à l'intérieur du coffret de 

"voltage dangereux" non isolé d'ampleur suffisante pour constituer un risque 

d'éléctrocution.

The exclamation point within an equilateral triangle is intended to alert the 

user of the presence of important operating and maintenance (servicing) 

instructions in the literature accompanying the appliance.

Le point d'exclamation à l'intérieur d'un triangle équilatéral est employé 

pour alerter les utilisateurs de la présence d'instructions importantes pour le 

fonctionnement et l'entretien (service) dans le livret d'instruction 

accompagnant l'appareil.

WARNING — To reduce the risk of fire or electric shock, do not 

expose this apparatus to rain or moisture.

Duration, 

per day in 

hours

Sound Level 

dBA, Slow 

Response

Typical Example 

8

90

Duo in small club

6

92

4

95

Subway Train

3

97

2

100

Very loud classical music

1.5

102

1

105

Greg and Ben screaming at Troy 

about deadlines

0.5 

110

0.25 or less 115

Loudest parts at a rock concert

PORTABLE CART

WARNING

Summary of Contents for PPM608

































Reviews: