background image

8

VLZ4 4•Bus

Typical Recording System

Once the band has played a few shows and feel that the songs are up to par, then it's time to record 

them for posterity and all three adoring fans. The good thing is that the VLZ4 4•Bus mixer functions great 

in both environments... live and recording!  

 

Here is how to record the band in three easy steps: 

 

1. Drum tracking: wire up everything as shown above. Bus the kick (panned left) to subgroup 1 and 

snare (panned right) to subgroup 2 so they are recorded to their own tracks in the DAW. They will show 

up on inputs 1 and 2. All four subgroup assign 1-2 Left/Right switches should be engaged so these 

signals may be monitored in mono. Bus the tom mics and overhead mics to subgroups 3 and 4; set the 

pans as preferred. The subgroup assign 3 left and subgroup assign 4 right switches should be engaged. 

These signals are recorded and monitored with the pan image as set up on the mixer and will show up 

as inputs 3 and 4. Check the levels carefully as they cannot be mixed later. The drums now need to be 

mixed in the DAW before overdubbing takes place.

 

 

2. Overdubbing: first, route the stereo USB return into the last stereo channel (23/24 or 31/32,  

depending on which VLZ4 4•Bus is being utilized). Next, route the stereo channel to the L/R Main 

so playback occurs in the headphones. Now route the bass to the L/R Main by sending the bass mic 

(panned left) to subgroup 1, and input 1 to track 5 of the DAW, while sending the bass DI (panned right) 

to subgroup 2, and input 2 to track 6 of the DAW. Finally, engage the subgroup assign 1 and 2 Left/

Right switches to hear the bass in mono. Congratulations, you are overdubbing with zero latency! 

 

3. Rinse and repeat: follow these same steps for guitars, keyboards, vocals, kazoos, llamas, and  

whatever else you can fit in the studio. It's that easy!

As the session progresses, the engineer, band, producer, A&R representative, and whatever posse may 

be present can crank the tunes through a pair of MR8mk3's and nod their collective heads to the beat.

POWER

ON

PHANTOM

ON

3

2

1

2

1

2

1

6

5

4

3

2

1

6

5

4

3

2

1

4

SUBGROUP OUTS

BAL / UNBAL

SUBGROUP INSERTS

TIP SEND, RINGRETURN

AUX INSERTS 

TIP SEND, RING RETURN

AUX SENDS 

BAL / UNBAL 

3

2

1

4

L

R

MONO

L

R

MONO

STEREO RETURNS 

BAL / UNBAL

21/22

23/24

BAL / UNBAL

BAL / UNBAL

MONITOR

MONO

MONITOR

L

R

100 - 240 V     

50 - 60 Hz  55W

TALKBACK

MIC

RIGHT

MAIN OUT

INSERT

LINE

LEFT

MAIN OUT

INSERT

LINE

MONO

MAIN OUT

INSERT

LINE

LEVEL

OUTPUT

L

USB

R

L

R

TAPE

OUT

IN

TIP SEND

RING RETURN 

TIP SEND

RING RETURN 

TIP SEND

RING RETURN 

BAL / UNBAL

BAL / UNBAL

 BAL / UNBAL

20

20

20

19

19

19

18

18

18

17

17

17

16

16

16

15

15

15

14

14

14

13

13

13

12

12

12

11

11

11

10

10

10

9

9

9

8

8

8

7

7

7

6

6

6

5

5

5

4

4

4

3

3

3

2

2

2

1

1

1

ONYX MIC PREAMPS

LINE

 (BAL / UNBAL)

INSERTS

 (TIP SEND, RING RETURN)

L

INE

 (BAL / UNBAL)

I

NSERTS

 (TIP SEND, RING RETURN)

ONYX MIC PREAMPS

UNBALANCED

REVISION

SERIAL NUMBER

REPLACE WITH THE SAME TYPE FUSE AND RATING.
DISCONNECT SUPPLY CORD BEFORE CHANGING FUSE

UTILISE UN FUSIBLE DE RECHANGE DE MÊME TYPE.
DEBRANCHER AVANT DE REMPLACER LE FUSIBLE

WARNING:

 TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR
MOISTURE.  DO NOT REMOVE COVER. NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL.

AVIS: RISQUE DE CHOC ELECTRIQUE — NE PAS OUVRIR

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES FOR THE U.S. AND THE ICES-003 FOR CANADA.  OPERATION 
IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND  
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE 
UNDESIRED OPERATION.

+6

U

power

input

reverb

master

gain

treble

middle

bass

volume

channel

1

1

2

gain

treble

middle

bass

volume

2

off

on

standby

TDSK

half

full

1

2

3

4

hi

lo

ultra hi / lo

5

master

standby

standby/

power/

fault

power

treble

frequency

midrange

bass

gain

-15dB

0dB

ks

pb

no

jd

pa

jh

Laptop 

Computer 

with audio 

production 

software

MR8mk3 

Powered Reference 

Monitors L/R

Headphone Amp

Headphones

Chris 

on keys

Francis

on bass

Amplifier

modeler

DI

Box

Dustin

on drums

desTROYer

on six-string

Anthony on 

lead vox

Summary of Contents for VLZ4









































Reviews: