background image

29

Owner’s Manual

Balanced XLR Output Connector

The male XLR connectors provide a balanced line-

 

level signal that represents the end of the mixer, where 
the fully mixed stereo signal enters the real world. 

 

Connect these to the left and right line-level inputs 
of powered speakers or to the left and right line-level 
inputs of an amplifier (with speakers already attached). 
Be sure the cables are wired per AES (Audio 

 

Engineering Society) standards:

Balanced XLR Output Connector

 

Pin 1 – Shield (Ground)

 

 

Pin 2 – Positive (+ or hot)

 

 

Pin 3 – Negative (– or cold)

Balanced 1/4" TRS Connector

TRS stands for Tip-Ring-Sleeve, the three  connections 

available on a stereo 1/4" cable. This allows for a direct 

connection to the channel input jacks. Be sure the 
cables are wired per AES (Audio Engineering Society) 
standards:

Balanced 1/4" TRS Connector

 

Sleeve – Shield (Ground)

 

 

Tip – Positive (+ or hot)

 

 

Ring – Negative (– or cold)

TRS jacks and plugs are used in several   different 

 

applications:

•  Balanced mono circuits. When wired as a 

 

balanced connector, a 1⁄4" TRS jack or plug 

 

is connected tip to signal high (hot), ring to 
signal low (cold), and sleeve to ground (earth).

•  Stereo Headphones, and rarely, stereo 

 

microphones and stereo line connections. 

 

When wired for stereo, a 1⁄4" TRS jack or plug 
is connected tip to left, ring to right and sleeve 
to ground (earth). VLZ4 mixers do not directly 
accept 1-plug-type stereo micro phones. They 
must be separated into a left cord and a right 
cord, which are plugged into the two mic 

 

preamps.

2

1

SHIELD

COLD

HOT

3

SHIELD

COLD

HOT

3

2

1

Balanced XLR Output Connector

SLEEVE

TIP

SLEEVE

TIP

RING

RING

TIP

SLEEVE

RING

Balanced 1/4" TRS Connector

 

You can cook up your own adapter for a stereo 
microphone. “Y” two cables out of a female 1⁄4" 
TRS jack to two male XLR plugs, one for the 

right signal and one for the left.

•  Unbalanced send/return circuits. When wired 

as a send/return “Y” connector, a 1⁄4" TRS jack 
or plug is connected tip to signal send (output 
from mixer), ring to signal return (input back 
into mixer), and sleeve to ground (earth).

Unbalanced 1/4" TS Connector

TS stands for Tip-Sleeve, the two connections 

 

available on a mono 1⁄4" cable. This allows for a direct 
conection to the channel input jacks. Be sure the cables 
are wired per AES (Audio Engineering Society) 

 

standards:

Unbalanced 1/4" TS Connector

 

Sleeve – Shield (Ground)

 

 

Tip – Positive (+ or hot)

TS jacks and plugs are used in many different 

 applications, always unbalanced. The tip is connected 

 

to the audio signal and the sleeve to ground (earth). 
Some examples:

•  Unbalanced microphones
•  Electric guitars and electronic instruments
•  Unbalanced line-level connections

Unbalanced RCA Connector

RCA-type plugs (also known as phono plugs) 

 

and jacks are often used in home  stereo and video 
equipment and in many other applications. RCA plugs 
are  unbalanced. Connect the signal to the center post 
and the ground (earth) or shield to the surrounding 
“basket.” Be sure the cables are wired per AES (Audio 
Engineering Society) standards:

Unbalanced RCA Connector

 

Sleeve – Shield (Ground)

 

 

Tip – Positive (+ or hot)

SLEEVE

TIP

TIP

SLEEVE

TIP

SLEEVE

Unbalanced 1/4" TS Connector

TIP

SLEEVE

TIP

SLEEVE

Unbalanced RCA Connector

Summary of Contents for VLZ4









































Reviews: