background image

9

Owner’s Manual

Rear Panel - Connections

1. Mic Ins

This is a female XLR connector that accepts a  

 

balanced mic or line level input from almost any type 

 

of source. These Onyx mic preamps feature higher 

 

fidelity and headroom rivaling any standalone mic 

 

preamp on the market today. These circuits are  
 excellent at rejecting hum and noise. 

The XLR inputs are wired as follows:

 

 

Pin 1 = Shield or ground

 

 

Pin 2 = Positive (+ or hot)

 

 

Pin 3 = Negative (– or cold)

Professional ribbon, dynamic, and condenser mics all 

sound excellent through these inputs. The mic/line  
inputs will handle any kind of level you can toss at 
them, without overloading.

Microphone-level signals are passed through the 

mixer's splendid microphone preamplifiers to become 

line-level signals.

The Onyx preamps accept balanced line-level signals 

because the mixer is equipped with a -20 dB pad on 
channels 1-16 (2404VLZ4) and channels    

 

1-24 (3204VLZ4) so hot signals may pass.

See Appendix B (page 31) for further details and 

some rather lovely drawings of the connectors you can 
use with your mixer. 

VLZ4 4•Bus Features

Phantom Power

Most modern professional condenser mics require  

48V phantom power, which lets the mixer send  

 

low-current DC voltage to the mic’s electronics  
through the same wires that carry audio. (Semi-pro 
condenser mics often have batteries to accomplish the 
same thing.) “Phantom” owes its name to an ability to 
be “unseen” by dynamic mics (Shure SM57/SM58, for 
instance), which don’t need  external power and aren’t 

affected by it anyway. 

Phantom power may be selected by pressing up on the  

mixer's phantom [21] switch.

Never plug   single-ended (unbalanced)  
micro phones, or ribbon mics into the mic  
input jacks if phantom power is on. Do not 

plug instrument outputs into the mic XLR input jacks 
with phantom power on,  unless you are certain it is safe 

to do so.

2. Line Ins

These 1/4" jacks share circuitry (but not phantom 

power) with the mic preamps, and can be driven by  
balanced or unbalanced sources.

To connect balanced lines to these inputs, use a 1⁄4" 

Tip-Ring-Sleeve (TRS) plug, wired as follows:

 

 

Tip = Positive (+ or hot)

 

 

Ring = Negative (– or cold)

 

 

Sleeve = Shield or ground

To connect unbalanced lines to these  inputs, use a 

1⁄4" mono (TS) phone plug, wired as follows:

 

 

Tip = Positive (+ or hot)

 

 

Sleeve = Shield or ground

POWER

ON

PHANTOM

ON

3

2

1

2

1

2

1

6

5

4

3

2

1

6

5

4

3

2

1

4

SUBGROUP OUTS

BAL / UNBAL

SUBGROUP INSERTS

TIP SEND, RINGRETURN

AUX INSERTS 

TIP SEND, RING RETURN

AUX SENDS 

BAL / UNBAL 

3

2

1

4

L

R

MONO

L

R

MONO

STEREO RETURNS 

BAL / UNBAL

21/22

23/24

BAL / UNBAL

BAL / UNBAL

MONITOR

MONO

MONITOR

L

R

100 - 240 V     

50 - 60 Hz  55W

TALKBACK

MIC

RIGHT

MAIN OUT

INSERT

LINE

LEFT

MAIN OUT

INSERT

LINE

MONO

MAIN OUT

INSERT

LINE

LEVEL

OUTPUT

L

USB

R

L

R

TAPE

OUT

IN

TIP SEND

RING RETURN 

TIP SEND

RING RETURN 

TIP SEND

RING RETURN 

BAL / UNBAL

BAL / UNBAL

 BAL / UNBAL

20

20

20

19

19

19

18

18

18

17

17

17

16

16

16

15

15

15

14

14

14

13

13

13

12

12

12

11

11

11

10

10

10

9

9

9

8

8

8

7

7

7

6

6

6

5

5

5

4

4

4

3

3

3

2

2

2

1

1

1

ONYX MIC PREAMPS

LINE

 (BAL / UNBAL)

INSERTS

 (TIP SEND, RING RETURN)

L

INE

 (BAL / UNBAL)

I

NSERTS

 (TIP SEND, RING RETURN)

ONYX MIC PREAMPS

UNBALANCED

REVISION

SERIAL NUMBER

REPLACE WITH THE SAME TYPE FUSE AND RATING.
DISCONNECT SUPPLY CORD BEFORE CHANGING FUSE

UTILISE UN FUSIBLE DE RECHANGE DE MÊME TYPE.
DEBRANCHER AVANT DE REMPLACER LE FUSIBLE

WARNING:

 TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR
MOISTURE.  DO NOT REMOVE COVER. NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL.

AVIS: RISQUE DE CHOC ELECTRIQUE — NE PAS OUVRIR

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES FOR THE U.S. AND THE ICES-003 FOR CANADA.  OPERATION 
IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND  
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE 
UNDESIRED OPERATION.

+6

U

3

14

20

2

13

1

16

11

17

12

22

7

7

9

18

21

19

4

15

5

10

8

8

8

6

Summary of Contents for VLZ4









































Reviews: