background image

5

Caution 

The Easy Fit System must be assembled prior to use . Should you have any questions 
during assembly contact your local authorized dealer .

•  Under no circumstance should the track, lift and sling(s) or entire system be put in control of a person 

who has not been properly trained in the use and care of this equipment . Failure to adhere to this warning 
may result in serious injury to the operator, and/or the individual being lifted/transferred .

•  Never install the Bottom foot plate on the top portion of post section or vice versa . See section 

‘Assembly’ 

instructions .

•  The 

Easy

 Fit System and associated lift and sling(s) are not toys . Do not use them for unsafe practices . Do 

not allow children to play with this equipment or any of its components .

•  The manufacturer’s warranty is void if persons unauthorized to perform work undertake this on the 

Easy

 

Fit System .

•  Ensure rubber feet are cleaned and dry prior to each use . See section 

“Cleaning Rubber Base Instructions.”

•  Ensure that the pressure gauge is in the safe zone during set up .
•  Check the posts during installation are level both visually and with master spirit level .

•  In places where more than one operator will be responsible for using the 

Easy

 Fit System, associated lift 

and sling(s), it is imperative that all operators be trained in its proper use .

•  Never expose the Easy Fit directly to water . Warranty does not cover any misuse or abuse of the Easy Fit 

system .

•  To maintain optimum function, the 

Easy

 Fit should be inspected and maintained on a regular basis . See 

the section titled “

Pre-Use Inspection and Maintenance”.

•  Any accessories used with the 

Easy

 Fit System including lift and sling(s), should be checked to ensure 

that they are in good working order . Check for signs of wear or fraying prior to use . Report any unusual 
wear or damage immediately to your local authorized dealer .

•  The 

Easy

 Fit System and associated lift, and sling(s) are intended only for lifting and transferring of 

a person . The manufacturer will not be responsible for any damage caused by the misuse, neglect or 
purposeful destruction of the lift and/or its associated components .

•  Do not in any circumstance exceed the maximum load for this piece of equipment . Refer to the 

“Specifications of the 

Easy

 Fit System”

 section of this manual .

•  The installation of the 

Easy

 Fit System, lift, accessories, and sling are certified to a maximum load . Do not 

exceed the maximum rated load of any of the components .

•  Ensure that a clear space is maintained around the 

Easy

 Fit System . Remove all furniture and other 

obstacles out of the way before performing a transfer .

•  The 

Easy

 Fit System has been designed to lift vertically at its maximum load and at maximum height . Do 

not attempt to lift an individual at an angle to the track .

Summary of Contents for 540100




























Reviews: