background image

- 13 - 

Inspections

End Users

Certified 

specialist

Check for free motion of the  
slide & tilt / parallel-stop unit and 
the smooth running and position of 
the handle in the closed position 
(precise vertical position upwards) 
and, if necessary, arrange for a  
certified specialist to readjust the 
slide & tilt / parallel-stop unit.

Check all hardware components 
and striker plates for obvious  
damage or wear (abrasion) and, 
if necessary, arrange for replace-
ment by a certified specialist.

Check all moving hardware 
components and striker plates for 
proper function and lubricate / 
oil them.

Check fixing screws and tighten 
or replace as necessary.

Setting of the gasket compression 
on the gear side, for standard and 
hook drive gears.

Checking the gasket compression 
for the locking cams or i.S. cams 
and readjusting as necessary.

 = only be undertaken by a certified specialist

Maintenance instructions

Your windows or casement doors are equipped with high quality and 
durable MACO hardware. The following maintenance instructions and 
prescribed intervals must be observed and followed in order to 
ensure that they remain functional and safe for years to come.

DANGER

WARNING

CAUTION

ACHTUNG

ACHTUNG

NOTICE

In addition to regular cleaning, window and casement door hardware 
requires regular inspection and maintenance to ensure usability and 
safety. We therefore recommend an appropriate maintenance 
contract with the manufacturer of your windows and casement doors.

Summary of Contents for RAIL-SYSTEMS S&T-S





















Reviews: