W134 N5345 Campbell Dr.
Menomonee Falls, WI 53051
800-238-7474
262-781-3366
Fax 262-781-4433
sales@macromatic.com
www.macromatic.com
I
NSTALLATION
I
NSTRUCTIONS
TD-8 S
ERIES
D
IGITAL
-S
ET
T
IME
D
ELAY
R
ELAY
901-0000-276
October, 2014 REV B
Installation
: Mount the appropriate 8 or 11 pin octal socket in a suitable enclosure. Wire the socket per the wiring diagram on the side
of the time delay relay. Make sure to match the terminal numbers on the socket to the ones shown on the wiring diagram (the wiring
diagram on the relay is the view looking towards the bottom of the relay vs. the top of the socket). Use #12-20 solid or stranded copper
or copper-clad aluminum wires with Macromatic sockets and a terminal tightening torque of 7 in-lbs. Plug the time delay relay into
the socket, making sure the key on the center post is in the proper orientation before insertion. If the relay must be removed from the
socket, do NOT rock the relay back and forth excessively—the center post could be damaged.
DANGER!
Potentially hazardous voltages are present. Electrical shock can cause death or serious injury.
Installation should be done by qualifi ed personnel following all National, State & Local Codes.
BE SURE TO REMOVE ALL POWER SUPPLYING THIS EQUIPMENT BEFORE CONNECTING OR DISCONNECTING WIRING.
READ INSTRUCTIONS BEFORE INSTALLING OR OPERATING THIS DEVICE. KEEP FOR FUTURE REFERENCE.
Troubleshooting:
If the unit fails to operate properly, check that all connections are correct per the appropriate wiring diagram on the
product. Refer to the description of the function operation on the next page. If problems continue, contact Macromatic at 800-238-7474
or e-mail
tech-support@macromatic.com
for assistance.
Warranty:
All Catalog-listed TD-8 Series Time Delay Relays manufactured by Macromatic are warranted to be free from defects in
workmanship or material under normal service and use for a period of fi ve (5) years from date of manufacture.
The following applies to only the TD-881 Series Multi-Function
unit (Figure 1):
Programming is accomplished through the use of two 10-position
DIP-switches. Switches A-D of the left-mounted DIP-switch are used
to select a function (as a guide, see the descriptions of how each
function operates on the reverse side of this sheet). Switches E, F
& G of the same DIP-switch are used to select the time base (t) for
single mode functions and (t1) for dual mode functions. Switches H,
J & K are used to select the time base (t2) for dual mode functions. A
convenient chart is on the side of the product to clearly illustrate how
to set both the function and time base.
The right-mounted 10-position DIP-switch is used to select the time
delay within the time base or bases selected with switches E-K from
the fi rst DIP-switch. Each position on the right-mounted DIP-switch is
marked with a time increment. The required delay, (t) for single mode functions or (t1) and (t2) for dual mode functions, is selected
by moving the switch of each increment to the ON position and adding their corresponding values. NOTE: Dual mode functions can either
have the same or different (t1) and (t2) times as well as different time bases. NOTE: Switches H, J ,& K are only used on dual mode
functions and are not used for single mode functions.
LED Indicator:
Green ON--Power, Red ON--Relay Energized
The following applies to all TD-8 Series Single-Function units
(Figure 2):
Programming is accomplished through the use of one 10-position
DIP-switch (single mode functions) or two 10-position DIP-switches
(dual mode functions). Each position on the DIP-switch is marked
with a time increment. The required delay, (t) for single mode
functions or (t1) and (t2) for dual mode functions, is selected by
moving the switch of each increment to the ON position and adding
their corresponding values.
As a guide, a description of how each function operates is on the
reverse side of this sheet.
LED Indicator:
Green ON--Power, Red ON--Relay Energized
Figure 1
Figure 2
Top
Side
Single Mode Functions
Dual Mode Functions
ON
ON
OFF
COMBINE FOR
TOTAL TIME
SEE CHART ON SIDE
FOR FUNCTION &
TIME BASE SETUP
TIME BASE
FUNCTION
A
B
C
D
-
-
-
-
-
-
-
-
-
-
E
F
G
H
J
K
64
256
512
128
32
16
4
8
2
1
-
-
-
-
-
-
-
-
-
-
1ST DELA
Y
2ND DELA
Y
1
4
2
8
16
1
2
4
8
DUAL
MODE
16
SINGLE
ON
ON
OFF
TIME DELAY
COMBINE FOR
TOTAL TIME
SEE CHART ON SIDE
FOR FUNCTION &
TIME BASE SETUP
TIME BASE
FUNCTION
A
B
C
D
E
F
G
H
J
K
64
256
512
128
32
16
4
8
2
1
t1
1
4
2
8
16
1
2
4
8
DUAL
MODE
16
SINGLE
MODE (t)
RED - RELAY ON
GRN - POWER ON
STATUS
t2
SELECT FUNCTION
A
B
C
D
ON DELAY
OFF OFF OFF OFF
INTERVAL ON
ON OFF OFF OFF
OFF DELAY
OFF ON OFF OFF
I
OFF
FLASHER (ON)
OFF OFF
FLASHER (OFF)
ON
OFF
WATCHDOG
OFF
ON
O
ON
ON OFF
OFF
OFF ON
CYCLE (ON)
ON
OFF
OFF
ON
ON ON
ON
ON OFF ON ON
OFF ON ON ON
ON ON ON ON
S
IN
G
LE
M
O
DE
BASE E
F
G
BASE
1 S
OFF ON OFF
0.1M OFF OFF ON
1M
ON ON OFF
1
1 H
ON ON
SINGLE MODE (t)
SELECT TIME BASE
DUAL
MODE
(t1)
(t2)
ONE SHOT
TR. DELAYED INT.
ON/OFF DELAY
DELAYED INTERVAL
CYCLE (OFF)
ON DELAY FLASHER
SELECT FUNCTION
FUNCTION
A
B
C
D
ON DELAY
OFF OFF OFF OFF
INTERVAL ON
ON OFF OFF OFF
OFF DELAY
OFF ON OFF OFF
O
O
O
OFF
FLASHER (ON)
OFF O
O
FLASHER (OFF)
ON O
O
OFF
WATCHDOG
OFF O
ON O
ONE SHOT F. EDGE
ON O
ON
O
OFF
OFF O
OFF ON
CYCLE (ON)
ON O
OFF O
OFF O
ON
ON ON O
O
O
O
N
O
ON
ON OFF ON ON
OFF ON ON ON
ON ON ON ON
S
IN
G
LE
M
O
DE
E
F
G
H
J
K
1 S
OFF ON OFF
0.1M OFF OFF ON
1M
ON ON OFF
0.1H
ON OFF ON
1H
OFF ON ON
SEL CT TIME BASE
DUAL
MODE
DUAL
MODE
ONE SHOT-FLASHER
TR. DELAYED INT.
ON/OFF DELAY
DELAYED INTERVAL
CYCLE (OFF)
ON DELAY/FLASHER
N
N
FF
FF
N
N
FF
FF
FF
N
N
FF
FF
N
FF
FF
N
N
FF
TR. ON DELAY
SINGLE SHOT
0
0.1 S ON OFF OFF
0.1 S ON OFF OFF
0. 1
OFF OFF
0.
S
OFF OFF
0
1 S
OFF ON OFF
0.1M OFF OFF ON
1M
ON ON OFF
1
1 H
ON ON
1 S
OFF ON OFF
0.1M OFF OFF ON
1M
ON ON OFF
0.1H
ON OFF ON
1H
OFF ON ON
0
0.1 S ON OFF OFF
0.1 S ON OFF OFF
0. 1
OFF OFF
0.
S
OFF OFF
0
O
OFF
ON
O
OFF
ON
NOTE:
SWITCHES H,
J,
&
K ARE ONLY USED ON DUAL MODE FUNCTIONS
64
COMBINE FOR
TOTAL TIME
IN SECONDS
256
128
512
-
-
-
8
-
32
16
-
-
-
2
-
-
4
-
1
ON
OFF
RED
-
RELAY
ON
GRN
-
POWER
ON
STATUS
t
64
-
256
512
-
128
-
-
8
-
32
-
16
-
-
2
-
4
-
1
64
-
256
512
-
128
-
-
8
-
32
-
16
-
-
2
-
4
-
1
ON
OFF
ON
COMBINE FOR
TOTAL TIME
IN MINUTES
t2
t1
RED
-
RELAY
ON
GRN
-
POWER
ON
STATUS
