Macsense Connectivity Digital Wattmeter DWM-4 Product Manual Download | Manualshive

Page: 6 / 12

background image

- 6 -

___

Install the .01uf monolithic capacitors, C1 and C2.

___

Install 1/8" stereo jack.

___

Unwrap the enclosure. Install the SO-239 connectors. Put one #4 screw in hole and place two
nuts on the screw. Repeat with the other three screws. Do not tighten them at this time.

___

Place the PC board onto the SO-239s. Align the 1/8” jack with the hole in the enclosure. Once
this is in place, you may tighten the nuts that are underneath the PC board. You do this by
pressing the board down on the nuts while turning the screw. Repeat with the other three screws.

___

Install the remaining four nuts on top of the PC board and tighten.

___

Solder the SO-239s to the PC board.

You are now finished with the VHF/UHF Remote Sensor.

«
...
4
5
6
7
8
...
»

Summary of Contents for Digital Wattmeter DWM-4













Reviews:

No comments

Related manuals for Digital Wattmeter DWM-4

Brand: Yamaha Pages: 2

Brand: B meters Pages: 18

Brand: B meters Pages: 14

Brand: Roland Pages: 15

Brand: VELOCICALC Pages: 10

VOLUTANK Petro 3003

Brand: Bartec Pages: 10

STORA-ABG RKS-01

Brand: ECOTEST Pages: 146

Brand: LaserLine Pages: 11

Brand: PASCO Pages: 4

DELMHORST J-2000

Brand: ABQ Industrial Pages: 4

Brand: General Pages: 12

Brand: Vectronics Pages: 2

Brand: Resol Pages: 24

Brand: Hanna Instruments Pages: 25

CR-2010 PRO Series

Brand: G-Tek Pages: 48

Brand: S&T Pages: 23

MASTERVISION ECO

Brand: Ega Master Pages: 48

PROline promag 23

Brand: Endress+Hauser Pages: 108

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands