MACTRAP Grease Boss G25 216 Operational Manual Download | Manualshive

Page: 1 / 9

background image

1

Mactrap Grease Boss Operational Manual v Feb 2017

OPERATIONAL MANUAL

MACTRAP Grease Boss G25 Model -216

Automatic Grease Removal Unit (GRU)

The picture above shows the MACTRAP Grease Boss with

optional

pump out unit at outlet end

Units are right or left hand inlet flow to suit customer location. The above example is left to right flow

Supplied and serviced By:

MACTRAP

For more information contact

MACTRAP

Phone: +64 7 549 0414 / Mobile: +64 274 978 791
Email: info@mactrap.co.nz www.mactrap.co.nz

Manufactured by MACTRAP Katikati New Zealand

1
2
3
...
»

Summary of Contents for Grease Boss G25 216










Reviews:

No comments

Related manuals for Grease Boss G25 216

Brand: Madas Pages: 44

Brand: Watermaid Pages: 38

Brand: OfiTE Pages: 37

Brand: Oase Pages: 36

AlwaysFresh HFC-1000

Brand: Waterline Technology Pages: 6

Brand: Waterdrop Pages: 2

CLARYUM AO-US-100-R

Brand: A.O. Smith Pages: 3

Brand: Crystal Quest Pages: 2

Thunder Reverse Osmosis

Brand: Crystal Quest Pages: 6

Brand: Crystal Quest Pages: 8

Brand: Crystal Quest Pages: 9

Brand: Crystal Mountain Pages: 4

Brand: Johnson Controls Pages: 4

Brand: EasyPro Pages: 3

FlowXtreme NE4487

Brand: Bluewave Pages: 20

Brand: BWT Pages: 66

Brand: Schenker Pages: 57

Brand: Aquaguard Pages: 115

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands