Macurco RD-xx User Manual
REV – 2.1
[34-2900-0511-7 ]
19
|
P a g e
4.4.1
Selecting Default Configuration – “dEF”
To select the Default Configuration, in normal mode, push the
Next
button to get to “Con” or the Configuration menu. Then
push the Enter button to enter the Con menu. The first selection is the “dEF” or Default setting. Push
Enter
. If it is already in
Default configuration, there will be no action. If it is not already in Default configuration, “nO” will be displayed. Push
Next
to
change it to “yES” (flashing) then push
Enter
to confirm the change (solid) and push
Enter
again to return to “dEF” in the con
menu. Push
Next
until “End” is displayed then push
Enter
to get back to normal operation.
Note: “dEF” menu cannot be changed during calibration due warning and calibration overdue trouble. Refer to Section
Calibration Period Settings – “CAL”
for Calibration Due Warning and Calibration Overdue trouble.
4.4.2
Power-Up Test Setting – “PUt”
To select the Power Up Test Configuration, in normal mode, push the
Next
button to get to “Con” or the Configuration menu.
Then push the
Enter
button to enter the Con menu. Then push the
Next
button to get to the second selection “PUt” or Power
Up Test setting. Push
Enter
. If the test is “On” push
Next
to turn it “OFF” (flashing) then push
Enter
to confirm the change (solid)
and push
Enter
again to return to “PUt” in the Con menu. Push
Next
until “End” is displayed then push
Enter
to get back to
normal operation.
4.4.3
Buzzer Setting – “bUZ”
To select the Buzzer Configuration, in normal mode, push the
Next
button to get to “Con” or the Configuration menu. Then push
the
Enter
button to enter the Con menu. The third selection is the “bUZ” or Buzzer setting. Push
Next
twice to get to “bUZ” then
Enter
. If the display is “On” push
Next
to turn it “OFF” (flashing) then push
Enter
to confirm the change (solid) and push
Enter
again to return to “bUZ” in the Con menu. Push
Next
until “End” is displayed then push
Enter
to get back to normal operation.
4.4.4
Alarm Relay Configuration – “Arc”
To select the Alarm Relay Configuration, in normal mode, push the
Next
button to get to “Con” or the Configuration menu. Then
push the
Enter
button to enter the Con menu. The fourth selection is the “Arc” or Alarm Relay Configuration. Push
Next
three
times to get to “Arc” then
Enter
. If the relay is “nO” (normally open) push
Next
to turn it to “nC” (flashing) then push
Enter
to
confirm the change (solid) and push
Enter
again to return to “Arc” in the Con menu. Push
Next
until “End” is displayed then
push
Enter
to get back to normal operation.
4.4.5
Fan Relay Delay Setting – “Frd”
To select the Fan Relay Delay setting, in normal mode, push the
Next
button to get to “Con” or the Configuration menu. Then
push the
Enter
button to enter the Con menu. The fifth selection is the “Frd” or Fan Relay Delay. Push
Next
four times to get to
“Frd” then
Enter
. If the delay is “0” (zero minutes) push
Next
to change it to 1, 3, 5, or 10 minutes (flashing) then push
Enter
to
confirm the change (solid) and push
Enter
again to return to “Frd” in the Con menu. Push
Next
until “End” is displayed then
push
Enter
to get back to normal operation.
4.4.6
Fan Relay Minimum Runtime Setting – “Frr”
To select the Fan Relay Minimum Runtime setting, in normal mode, push the
Next
button to get to “Con” or the Configuration
menu. Then push the
Enter
button to enter the Con menu. The sixth selection is the “Frr” or Fan Relay Minimum Runtime. Push
Next
five times to get to “Frr” then
Enter
. If the runtime is “0” (zero minutes) push
Next
to change it to 3, 5, 10 or 15 minutes
(flashing) then push
Enter
to confirm the change (solid) and push
Enter
again to return to “Frr” in the Con menu. Push
Next
until
“End” is displayed then push
Enter
to get back to normal operation.
4.4.7
Fan Relay Latching Setting – “FrL”
To select the Fan Relay Latching Option, in normal mode, push the
Next
button to get to “Con” or the Configuration menu. Then
push the
Enter
button to enter the Con menu. The seventh selection is the “FrL” or Fan Relay Latching Option. Push
Next
six
times to get to “FrL” then
Enter
. If latching is “OFF” push
Next
to turn it to “On” (flashing) then push
Enter
to confirm the
change (solid) and push
Enter
again to return to “FrL” in the Con menu. Push
Next
until “End” is displayed then push
Enter
to
get back to normal operation.
