Mad Bean Pedals Harbinger Two Manual Download

Page: 6 / 13

Parts Guide

15v Zener:

https://www.mouser.com/ProductDetail/ON-Semiconductor-Fairchild/1N4744A?qs=sGAEpiMZZMtQ8nqTK

tFS%2fD313Kx94AdFdSPLy44WWjs%3d

2n5089:

http://smallbear-electronics.mybigcommerce.com/transistor-2n5089/

2n5088:

http://smallbear-electronics.mybigcommerce.com/transistor-2n5088/

MPSA13:

http://smallbear-electronics.mybigcommerce.com/transistor-mpsa13/

MPF102:

http://smallbear-electronics.mybigcommerce.com/transistor-fet-mpf102/

LM7815:

http://smallbear-electronics.mybigcommerce.com/ic-lm7815ct/

NSL32:

http://smallbear-electronics.mybigcommerce.com/photocoupler-silonex-nsl-32/

LT1054:

http://smallbear-electronics.mybigcommerce.com/ic-lt1054cp/

SPDT:

http://smallbear-electronics.mybigcommerce.com/spdt-on-on-short-lever/

500R 3362p:

https://www.mouser.com/ProductDetail/Bourns/3362P-1-501LF?qs=sGAEpiMZZMvygUB3GLcD7iDNlz%2f

NDKompMEyhqEJhVo%3d

or,

https://www.taydaelectronics.com/potentiometer-variable-resistors/cermet-potentiometers/3362p/500-ohm-trimmer-po

tentiometer-cermet-1-turn-3362p.html

250k 3362p:

https://www.mouser.com/ProductDetail/Bourns/3362P-1-254LF?qs=sGAEpiMZZMvygUB3GLcD7p0sIDtXd

CwsKR9Dy6lj2rI%3d

or, (200k is okay):

https://www.taydaelectronics.com/potentiometer-variable-resistors/cermet-potentiome

ters/3362p/200k-ohm-trimmer-potentiometer-cermet-1-turn-3362-3362p.html

9mm Pots:

http://smallbear-electronics.mybigcommerce.com/alpha-single-gang-9mm-pc-mount/

12mm pots (50kB, 100kB):

http://smallbear-electronics.mybigcommerce.com/alpha-single-gang-12mm-solder-terms/

Wah Parts:

Your best bet is to find a used Crybaby and gut it. You can often find them in the $30-50 range. The advantage is that is

will cost less than purchasing an empty shell AND ICAR pot, jacks, etc. Plus, the wah pot is already mounted which is a

BIG advantage. Tip: you do not need to spend a lot on a fancy Wah pot. In the Harbinger Two it only controls the bright

ness of the LEDs in the two NSL-32.

smallbear does offer this shell:

http://smallbear-electronics.mybigcommerce.com/expression-pedal-shell/

and, this kit:

http://smallbear-electronics.mybigcommerce.com/expression-pedal-shell-kit/

And, this pot: http://smallbear-

electronics.mybigcommerce.com/wah-pot-the-black-bear-100k/

LDR:

smallbear does offer two versions of excellent LDRs for a Univibe:

http://smallbear-electronics.mybigcommerce.com/photocell-silonex-advanced-photonix-hi-dark-nsl-7532/

and,

http://smallbear-electronics.mybigcommerce.com/photocell-silonex-advanced-photonix-hi-dark-to-5/

Both appear to be out of stock at this time. In their absence, I recommend any of these (I’ve used the 7532 in other builds

with good success).

http://smallbear-electronics.mybigcommerce.com/photocell-silonex-advanced-photonix-nsl-7532/

http://smallbear-electronics.mybigcommerce.com/photocell-silonex-advanced-photonix-nsl-7530/

or, the 9203:

http://smallbear-electronics.mybigcommerce.com/photocells-cds-5mm-diameter/

Summary of Contents for Harbinger Two














Search results

Summary of Contents for Harbinger Two

Reviews:

Related manuals for Harbinger Two

Brands by name

Popular brands

Mad Bean Pedals Harbinger Two, Manual

Search results

Summary of Contents for Harbinger Two

Reviews:

Related manuals for Harbinger Two

Brands by name

Popular brands