background image

[Part 3] Using MADRIX 5 Software

//24

www.madrix.com

MADRIX STELLA User Manual

§

9] Optimized Frames Or Full Frames

§

10] Sync Mode

§

Additional Art-Net Device Settings

DMX-OUT Via Ethernet Network [Art-Net]

You can connect the STELLA over Ethernet network  to  the  network  card  of  your  computer  that  runs  the  MADRIX  5

Software. Data is distributed to the STELLA over network cabling  [Ethernet]  and  sent  to  the  two  ports  [DMX  1  and

DMX 2].

1] Initial Configuration

§

Put MADRIX STELLA into operation; as described above. Learn more »

Putting The Device Into Operation

 

§

Connect MADRIX STELLA to your computer using Ethernet network cabling.

§

It is highly recommended to use Gigabit Ethernet network components [network card, switches, etc.].

§

Set up the corresponding settings in the »

Configuration Using A Web Browser

2] Windows Network Settings

Art-Net is a network-based protocol. MADRIX 5 will use the network card of your computer to send data. 

§

It is required to set up the correct network settings in Windows, first.

§

You must use these IP address and Subnet mask settings. Otherwise, Art-Net might not work!

§

The IP addresses of your computer and your MADRIX STELLA devices need to be different.

Summary of Contents for STELLA




















































































































Reviews: