background image

[Part 3] Using MADRIX 5 Software

//35

www.madrix.com

MADRIX STELLA User Manual

DMX-OUT Over Ethernet Network [Streaming ACN / sACN]

You can connect the STELLA over Ethernet network  to  the  network  card  of  your  computer  that  runs  the  MADRIX  5

Software. Data is distributed to the device over network cabling [Ethernet] and sent to the output ports [DMX  1  and

DMX 2].

1] Initial Configuration

§

Put MADRIX STELLA into operation; as described above. Learn more »

Putting The Device Into Operation

 

§

Connect MADRIX STELLA to your computer using Ethernet network cabling.

§

It is highly recommended to use Gigabit Ethernet network components [network card, switches, etc.].

§

Set up the corresponding settings in the »

Configuration Using A Web Browser

2] Windows Network Settings

§

MADRIX 5 automatically sets up Streaming ACN network settings for you.

[MADRIX 5 supports multicast Streaming ACN. Data is automatically sent to all corresponding sACN devices in the

network. Unicast is also supported.] 

§

You only need a computer with a network card and a valid IP address.

§

You do not have to change the IP address settings in Windows for Streaming ACN!

§

The  IP  address  range  for  sACN  devices  is  239.255.X.X  according  to  the  Streaming  ACN

specifications. MADRIX STELLA automatically works this way.

§

Make sure that your Firewall does not block data of the 239.255.X.X IP address range!

§

Check the settings of the Windows Firewall. 

§

Learn more »

Tips [Microsoft Windows / Networks / USB]

 

Summary of Contents for STELLA




















































































































Reviews: