background image

506325-01

Issue 1734

Page 1 of 15

Save these instructions for future reference

INSTALLATION AND MAINTENANCE INSTRUCTIONS

MHP4 Series

Self-Contained Heat Pump

Manufactured By

Allied Air Enterprises LLC

A Lennox International Inc. Company

215 Metropolitan Drive

West Columbia, SC 29170

This is a safety alert symbol and should never be ignored. When you see this symbol on labels or in 

manuals, be alert to the potential for personal injury or death.

Improper installation, adjustment, alteration, service, or 

maintenance can cause injury or property damage. Refer 

to this manual. For assistance or additional information, 

consult a qualified installer or service agency.

 WARNING

Table of Contents

Installation ...................................................................2

Operation .....................................................................7

Maintenance ................................................................9

Accessories ...............................................................10

Wiring Diagrams ........................................................12

The installation of this appliance must conform to the requirements of the National Fire Protection Association; the National 

Electrical Code, ANSI/NFPA No. 70 (latest edition) in the United States; the Canadian Electrical Code Part 1, CSA 22.1 

(latest edition) in Canada; and any state or provincial laws or local ordinances. Local authorities having jurisdiction should 

be consulted before installation is made. Such applicable regulations or requirements take precedence over the general 

instructions in this manual.

 CAUTION

For your safety, do not store or use gasoline or other 

flammable vapors and liquids in the vicinity of this or any 

other appliance. Such actions could result in property 

damage, personal injury, or death.

 WARNING

Installation and servicing of air conditioning equipment 

can be hazardous due to internal refrigerant pressure 

and live electrical components. Only trained and 

qualified  service  personnel  should  install  or  service 

this equipment. Installation and service performed by 

unqualified  persons  can  result  in  property  damage, 

personal injury, or death.

 WARNING

The unit must be installed with approved wall sleeve 

and grille accessories for safe operation. Improper 

installations could result in property damage, personal 

injury, or death.

 WARNING

 

(P) 506325-01

*P506325-01*

Summary of Contents for MHP-10-24
















Reviews: