background image

m

File information

Settings related to the image file to be printed using the UV ink.

Memo:

v

This setting is enabled when [Extraction]-[File] for the front side or
back side is specified.

m

Name

Registered name of the image file. You can enter a name up to 30
characters.

m

File

Image file. Click the [Select] button to select a file.
"Windows Bitmap File Format" (

A

 page 93)

m

X

X coordinate where printing of the image file starts. (Unit: mm).
When [Orientation] inside the [Setup] tab is set to [Landscape], the
value is 0.00 to 87.4. When [Portrait] is set, the value is 0.00 to 55.9.
Data outside the printing area is not printed.

m

Y

Y coordinate where printing of the image file starts. (Unit: mm).
When [Orientation] inside the [Setup] tab is set to [Landscape], the
value is 0.00 to 55.9. When [Portrait] is set, the value is 0.00 to 87.4.
Data outside the printing area is not printed.

m

Side

The side of the card for which the printing area is valid.

v

1. Front:
Front side

v

2. Back:
Back side

m

[Add] button

Registers the input data. You can enter up to 8 input data.

m

[Delete] button

Deletes the information selected in the list.

m

[Delete All] button

Deletes all registered information.

m

Number of panels using the retransfer film

Number of retransfer film panels to be used.

v

Auto:
Automatically prints one panel of the retransfer film when the data
of other ink types does not overlap with the UV ink printing
position.

v

1 panel:
Always prints one panel of the retransfer film. When the data of
other ink types overlaps with the UV ink printing position, the data
of the ink types will be adjusted.

v

2 panels:
Always prints two panels of the retransfer film.

"Number of retransfer film panels during printing" (

A

 page 93)

Priority of printing data

v

An extracted text has a higher priority than an image file, and is
always printed on the top.

v

The image files are processed in the order of registration. When
there is overlap in the printing areas, the older data will be
overwritten by the data of the image file that is registered later.

Page Number for the Printed Document and Page Split
Settings

.

v

When [Page split] is not set, UV ink data is extracted from the YMC
ink data, or the UV ink image file is used.

MAC Address Position

v

In the case of UV ink printing, the printer always prints the MAC
address.

v

The printing position of the MAC address can be set separately for
the front and back sides using the printer driver. The two positions
below can be selected.

m

[Landscape] Orientation

.

1234-5678-90AB

1234-5678-90AB

A

C

B

D

A

 MAC address printing position when [Upper Right] is selected

B

 MAC address printing position when [Lower Left] is selected

C

 (X=0, Y=0)

D

 (X = approx. 87.5 mm, Y = approx. 56.0 mm), (X = 1035 pixel,

Y = 663 pixel)

MAC

Address

Printing

Position

Starting

X

Starting

Y

Width

Height

A

Upper

Right

64.69 mm

1.52 mm

19.47
mm

2.88
mm

764 pixel

18 pixel

230
pixel

34 pixel

B

Lower

Left

3.56 mm

51.73 mm

19.47
mm

2.88
mm

42 pixel

611 pixel

230
pixel

34 pixel

Setup

92

Summary of Contents for PRIMA401





























































































































Reviews: