14
ID 250E
EN
www.magmaweld.com
USER MANUAL | РУКОВОДСТВО ПО ЭКСПЛУАТАЦИИ | KULLANIM KILAVUZU
Make sure that all the materials you have ordered have been received. If any material is missing or damaged,
contact your place of purchase immediately.
The standard box includes the following;
• Welding machine and connected mains cable
• Warranty certificate
• Workpiece clamp and cable
• User manual
• Electrode clamp and cable
In case of a damaged delivery, record a report, take a picture of the damage and report to the transport
company together with a photocopy of the delivery note. If the problem persists, contact the customer service.
2.2 Installation and Operation Recommendations
Symbols and their meanings on the device
Welding may be dangerous. For welding should ensure proper working conditions, and the authorized
person should take necessary precautions. Specialists are responsible for the machine and have to be
equipped with the necessary equipment and those who are not relevant should be kept away from the
welding area.
This device is not compatible with IEC 61000-3-12. If it is desired to connect to the low voltage
mains used in homes, it is essential that the installer or the person who will operate the machine
to make the electrical connection must have the information on the machine’s connectivity. In this
case, the person who will perform the installation or the operator will assume responsibility.
The safety symbols and warning notes on the device and in the operating instructions must be observed
and the labels must not be removed.
Grids are intended for ventilation. The openings should not be covered to provide good cooling and no
foreign objects should be inserted.
• For better performance, place the machine at least 30 cm away from surrounding objects. Beware of
overheating, dust and humidity around the machine. Do not operate the machine in direct sunlight. In
cases where the ambient temperature exceeds 40°C, operate the machine at lower current or at a higher
cycle rate.
• Avoid welding outdoors in the presence of wind and rain. If welding is necessary in such cases, protect the
welding area and the welding machine with curtains and awnings.
• When positioning the machine, make sure that materials such as walls, curtains and panels do not prevent
easy access to the control and connections of the machine.
• If welding indoors, use a suitable fume extraction system. If there is a risk of breathing welding fumes and
gas indoors, use breathing apparatus.
• Follow the duty cycle rates specified on the product label. Exceeding duty cycle rates frequently can
damage the machine and void the warranty.
• Supply cable suitable for the specified fuse value should be used.
• Connect the ground wire tightly as close as possible to the weld area. Do not allow welding current to flow
over equipment other than welding cables.
• Welding cables and mains cable must not be wrapped around the machine body during operation.
INSTALLATION
2.1 Delivery Control
Installation
Summary of Contents for ID 250E
