19
ID 250E
EN
www.magmaweld.com
USER MANUAL | РУКОВОДСТВО ПО ЭКСПЛУАТАЦИИ | KULLANIM KILAVUZU
MAINTENANCE AND SERVICE
• Maintenance and repairs to the machine must be carried out by qualified persons. Magmaweld is not
responsible for accidents that may occur as a result of interventions by unauthorized persons.
• You can obtain the parts to be used in the repairs from our authorized services. The use of original spare parts
will extend the life of your machine and prevent performance losses.
• Always contact Magmaweld or an authorized service specified by Magmaweld.
• All warranty provisions will become void due to any interference not authorized by Magmaweld within the
warranty period.
• Make sure you comply with the applicable safety rules during maintenance and repair works.
• Disconnect the machine’s plugs from the mains before carrying out any repairs and wait for 10 seconds for
the capacitors to discharge.
4.1 Maintenance
Daily Maintenance
• Do not remove the warning labels on the device. Replace the worn/torn labels with
the new ones. Labels can be obtained from the authorized service.
• Check your torch, clamps and cables. Pay attention to the connections and the
durableness of the parts. Replace the damaged/defective parts with the new ones.
Do not ever make additions to/repair the cables.
• Ensure adequate space for ventilation.
• Before starting welding, check the gas flow rate from the tip of the torch with a flow
meter. If the gas flow is high or low, bring it to the appropriate level for the welding
process.
• Clean and tighten fasteners such as bolts and nuts.
• Check the electrode clamp and grounding clamp cables.
• Open the side covers of the machine and clean with low pressure dry air. Do not
apply compressed air to electronic components at close distance.
• Check the socket to which the power supply plug of the machine is connected. If
there is any looseness in the power cable connection points of the socket, remove
such looseness. If there is an arc or expansion in the socket slots, replace them with
new ones.
• Check the power supply plug of the machine. If there is any looseness in the power
cable connection points in the electricity plug, remove such looseness. If there is an
arc or deformation at the ends of the plug, replace it with a new one.
or
Every 6 Months
NOTE: The above mentioned periods are the maximum ones that should be applied if no problems are
encountered in your device. Depending on the work load and contamination of your work environment,
you can repeat the above processes more frequently.
Maintenance and Service
Summary of Contents for ID 250E
