EN
14
monoTIG 165ip / monoTIG 200ip
www.magmaweld.com
USER MANUAL
INSTALLATION
2.1 Delivery Control
2.2 Installation and Operation Recommendations
Make sure that all the materials you have ordered have been received. If any material is missing or damaged,
contact your place of purchase immediately.
Scope of supply;
• Welding machine and connected mains cable
• Workpiece clamp and cable
• Warranty certificate
• Torch
• User manual
In case of a damaged delivery, record a report, take a picture of the damage and report to the transport
company together with a photocopy of the delivery note. If the problem persists, contact the customer service.
Symbols and their meanings on the device
Welding may be dangerous. Proper working conditions should be ensured and necessary
precautions should be taken. Specialists are responsible for the machine and have to be equipped with the
necessary equipment and those who are not relevant should be kept away from the welding area.
This device is not compatible with IEC 61000-3-12. If it is desired to connect to the low voltage mains used
in homes, it is essential that the installer or the person who will operate the machine to make the electrical
connection has information on the machine’s connectivity. In this case the responsibility will be assumed
by the person who will perform the installation or by the operator.
The safety symbols and warning notes on the device and in the operating instructions must be observed
and the labels must not be removed.
Grids are intended for ventilation. The openings should not be covered in order to provide good cooling and
no foreign objects should be inserted.
Installation
• For a better performance, place the machine at least 30 cm away from the surrounding objects. Pay attention
to overheating, dust and moisture near the machine.
• Do not operate the machine under direct sunlight. If the ambient temperature exceeds 40°C, operate the
machine at a lower current or a lower duty cycle.
• Avoid welding outdoors in windy and rainy weather circumstances. If welding is necessary in such cases,
protect the welding area and the welding machine with a curtain and canopy. If you weld indoors, use a
suitable fume extraction system. Use breathing apparatus if there is a risk of inhaling welding fumes and gas
in confined spaces.
• When positioning the machine, make sure that materials such as walls, curtains, panels, etc. do not impede
easy access to the controls and connections of the machine.
• Observe the duty cycle rates specified on the product label. Exceeding duty cycle rates can damage the
machine and this may invalidate the warranty.
• Use the fuse that is compliant with your system.
• Secure the ground cable as close as possible to the welding area.
• Do not allow the welding current to pass through equipment other than the welding cables.
• The welding cables and the mains cable must not be wrapped in the machine housing during operation.
• When the gas cylinder is placed on the machine, immediately fasten the chain to secure the gas cylinder. If you
do not place the gas cylinder on the machine, fasten it to the wall with a chain
Summary of Contents for monoTIG 165ip
