EN
29
monoTIG 165ip / monoTIG 200ip
www.magmaweld.com
USER MANUAL
Maintenance and Service
E19
Thermal
Protection
(Secondary)
• Visually check if the fan is working
• If the problem continues, contact the
authorized service
• Unblock the front of the air ducts
• If the problem continues, contact the
authorized service
• Fan may not be working
• The front of the air inlet - outlet ducts
may be blocked
• The machine working environment
may be too hot or stuffy
• The uptime of your machine may have
been exceeded
• Make sure that the working
environment of the machine is not
excessively hot or stuffy
• If the problem continues, contact the
authorized service
• Allow the machine to cool down by
waiting for a while. If the fault
disappears, try to use the machine at
lower amperage values
• If the problem continues, contact the
authorized service
• Make sure that the torch shield is
correctly fitted to the machine
• If the problem continues, contact the
authorized service
• Torch shield may not be installed or
properly fitted
• Mains voltage may have decreased
• Mains voltage may have increased
E27
E29
E30
Torch Shield Not
Installed
DC Busbar
Voltage Low
DC Busbar
Voltage High
• Check the mains connection cables
and the voltage. Make sure the
correct voltage input is providevd.
If the mains voltage is normal,
contact the authorized service
• Check the mains connection cables
and the voltage. Make sure the
correct voltage input is provided.
If the mains voltage is normal,
contact the authorized service
E26
• Check your air / gas connections,
make sure that the inlet pressure
is appropriate. If the inlet pressure is
normal, contact the authorized
service
• Inlet pressure may be low
Inlet Pressure
Low
E14
E16
E17
E18
E20
E21
E22
E23
E28
E31
E15
System Error
System Error
System Error
System Error
System Error
Remote Control
Communication
Error
• Contact the authorized service
• Contact the authorized service
• Contact the authorized service
• Contact the authorized service
• Contact the authorized service
• Check remote control connections
• If the problem continues, contact the
authorized service
• There may be a hardware error
• There may be a hardware error
• There may be a hardware error
• There may be a hardware error
• There may be a hardware error
• There may be an error in the remote
control connections
Solution
Error
Error Code
Cause
Summary of Contents for monoTIG 165ip
