BLUEPIRAT RAPID | USER MANUAL/
page 39 of 67
14
Technical data (preliminary, modifications possible)
General data
BLUEPIRAT Rapid
BLUEPIRAT Rapid 100+
BLUEPIRAT Rapid 100+ Light
Nominal power supply volt-
age
13,8 V
13,8 V
Power supply voltage
7 to 28 V at system start up
6 to 30 V when running
dive/- 8%
7 to 28 V at system start up
6 to 30 V when running
dive/- 8%
Reverse polarity protection
of the supply voltage
yes
yes
Resistance to short-circuit-
ing
yes
yes
Power consumption / oper-
ating (typ.)
3,5
– 4,0 A (@ 12,0 V)
3,5
– 4,0 A (@ 12,0 V))
Power consumption / oper-
ating (peak.)
10,0 A (@ 12,0 V)
10,0 A (@ 12,0 V)
Power consumption /
standby
tbd
< 10 mA
Operating temperature
-30°C to + 70°C for data recording
-15°C to + 65°C for data recording
Storage temperature
- 40 °C to + 85 °C
- 40 °C to + 85 °C
Weight (ca.)
~ 4100 g
~ 4100 g
Power Management
BLUEPIRAT Rapid 100+
BLUEPIRAT Rapid 100+ Light
Startup time
from standby to full opera-
tion
ca. 80 s
ca. 80 s
Start of logging -
starting from standby
CAN, LIN, FlexRay, Serial, Analog, Digital
< tbd
CAN, LIN, FlexRay, Serial, Analog, Digital
< 4s
Start of logging from the
stand-by mode
tbd
100Base-T1 < 350ms
Start of forwarding from the
stand-by mode
tbd
Standby Mode
Configurable time for activation
Configurable time for activation
Wake
HS-CAN, LS-CAN, LIN, Seriell, KL 15,
100Base-T1, Dig IN
[ON / Trigger] -Taste
HS-CAN, LS-CAN, LIN, Seriell, KL 15,
100Base-T1, Dig IN
[ON / Trigger] -Taste
Data loss by power loss
If the device is switched off due to sudden
power loss, up to 60 sec. of data may be lost.
If the device is switched off due to sudden
power loss, up to 60 sec. of data may be lost.
Case
BLUEPIRAT Rapid 100+
BLUEPIRAT Rapid 100+ Light
Size (ca.)
252 x 70 x 200 mm
(B x H x T)
252 x 70 x 200 mm
(B x H x T)
Operating controls
Push-button to start and shut down data log-
ger and to set markers
Push-button to start and shut down data log-
ger and to set markers
LEDs
yes 4x
yes 4x
Connectors
BLUEPIRAT Rapid 100+
BLUEPIRAT Rapid 100+ Light
Front connectors
2 x 10GBase-T (RJ45),
2 x USB 3.0 (5V/900mA per Port)
4 x 1000Base-T (RJ45)
2 x 10GBase-T (RJ45),
2 x USB 3.0 (5V/900mA per Port)
4 x 1000Base-T (RJ45)
Rear connectors
20 x MATEnet
….
1 x SUB-D 78-pol:
1 x SUB-D 15-pol:
2 x DSUB COMBO 7W2
20 x MATEnet
….
1 x SUB-D 78-pol:
1 x SUB-D 15-pol:
2 x DSUB COMBO 7W2
Data recording
BLUEPIRAT Rapid 100+
BLUEPIRAT Rapid 100+ Light
Storage type (internal)
M2 SSD memory modules
M2 SSD memory modules
Storage size (internal)
1,5 TB / 3 TB
Up to 2.88 TB, thereof 480 GB for system &
connection-oriented logging
SSD Endurance pro SSD after JEDEC (En-
terprise Workload):
- Drive
Writes Per Day (DWPD): ≥0,51 (ser-
vice life: 3 years)
3 TB
Thereof 480 GB for system & connection-ori-
ented logging
SSD Endurance pro SSD after JEDEC (En-
terprise Workload):
-
Drive Writes Per Day (DWPD): ≥0,51 (ser-
vice life: 3 years)
Storage type (external)
various
various
Recording modes
normal, buffer
normal, buffer
Data performance
High-speed logging (FPGA based):
- Recording with up to 1,4 Gbit/s, depending
i.a. on logger memory configuration
High-speed logging (FPGA based):
- Recording with up to 1,0 Gbit/s, depending
i.a. on logger memory configuration
