background image

6

1. The LED indicator will provide information on 7 modes of security system operation:

LED is off = Security system is disarmed. 

LED is flashing = Security system is armed. 

LED is flashing fast = Automatic arming timer or RF protection mode timer is counting down. 

LED is on solid = Security system is in valet mode. (Only when the ignition key is on)

LED is flashing once every 5 seconds = Security system is in valet mode (Only when ignition key is off)

LED is flashing in a 2 flash-pause sequence = Tamper warning - security system has been trigger from

the hood/trunk switch or electronic sensor.  

LED is flashing in a 3 flash-pause sequence = Tamper warning - security system has been triggered

from an opened door.                                                  

2. The horn/siren will provide information on 4 modes of security system operation:

One horn/siren chirp = Security system is armed. 
One horn/siren chirp + One more chirp 5 seconds after the first chirp = Security system is armed but

one of the sensors was on and the alarm has bypassed it. The remaining sensors are armed. 

Two horn/siren chirps = Security system is disarmed.
Four horn/siren chirps = Tamper w security system is disarmed. 

Option #1: Remote Power Door Lock/Unlock Control

Note: Your vehicle must have an electronic door locking system for this feature to operate.

Installing option #1 will allow the remote transmitter supplied with your security system to lock and unlock
your vehicle’s doors as it arms and disarms your security system.

Option #2: Remote Trunk/Hatch Release (CH #2)

Installing option #2 will allow the remote transmitter supplied with your security system to open your
vehicles trunk or rear hatch. Pressing the “AUX” button on the transmitter for 4 seconds will open the
existing power trunk/hatch release mechanism.

Note:  Vehicles that are not factory equipped with an electronic trunk release system will require additional
parts than a vehicle with a factory installed trunk release system.

Option #3: Single Zone Shock Sensor 

Installing option #3 will increase the level of security provided by your security system. If the shock sensor
becomes activated the security system will immediately trigger your system by sounding the horn/siren and
flashing the parking lights.

Option #4: Starter Disable Relay

Adding option #4 will increase the level of protection that your security system can offer. When the starter
disable relay is installed, the vehicles engine will not crank when the alarm system is in the armed mode.

Alarm Mode Indicators

Upgrade Options

Summary of Contents for PL30









Reviews: