1 Notice
MAGNAVOX and SMART. VERY SMART. are registered trademarks
of Koninklijke Philips N.V. and are used under license from
Koninklijke Philips N.V.
Funai reserves the right to change products at any time without
being obliged to adjust earlier supplies accordingly.
The material in this Owner’s manual is believed adequate for the
intended use of the system. If the product or its individual modules
or procedures are used for purposes other than those specified
herein, confirmation of their validity and suitability must be
obtained. Funai warrants that the material itself does not infringe
any United States patents. No further warranty is expressed or
implied.
Funai cannot be held responsible neither for any errors in the
content of this document nor for any problems as a result of the
content in this document. Errors reported to Funai will be adapted
and published on the Funai support website as soon as possible.
Pixel characteristics
This LCD product has a high number of color pixels. Although it
has effective pixels of 99.999% or more, black dots or bright
points of light (red, green or blue) may appear constantly on the
screen. This is a structural property of the display (within common
industry standards) and is not a malfunction.
Warranty
No components are user serviceable. Do not open or remove
covers to the inside of the product. Repairs may only be done by
service centers and official repair shops. Failure to do so shall void
any warranty, stated or implied.
Any operation expressly prohibited in this Owner’s manual, any
adjustments or assembly procedures not recommended or
authorized in this Owner’s manual shall void the warranty.
Federal communications commission notice
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
●
Reorient or relocate the receiving antenna.
●
Increase the separation between the equipment and the
receiver.
●
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
●
Consult the dealer or an experienced radio or television
technician for help.
Declaration of conformity
Trade name
:
MAGNAVOX
Responsible party
:
FUNAI CORPORATION, Inc.
Model
:
55MV387Y, 50MV387Y
Address
:
19900 Van Ness Avenue, Torrance, CA
90501 U.S.A.
Telephone number
:
1 866 341 3738
Modifications
This apparatus may generate or use radio frequency energy.
Changes or modifications to this apparatus may cause harmful
interference.
Any modifications to the apparatus must be approved by Funai.
The user could lose the authority to operate this apparatus if an
unauthorized change or modification is made.
Cables
Connections to this device must be made with shielded cables
with metallic RFI / EMI connector hoods to maintain compliance
with FCC Rules and regulations.
Canadian notice
CAN ICES-3 (B)/NMB-3 (B)
Analog and digital television receiving apparatus, Canada BETS-7 /
NTMR-7.
The following FCC/IC RSS applies to the wireless LAN
adapter included in this product.
FCC caution: Any changes or modifications not expressly
approved by the party responsible for compliance could void
the user’s authority to operate this equipment.
This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
Country code statement
For product available in the USA market, only channel 1~11
can be operated. Selection of other channels is not possible.
To maintain compliance with FCC RF exposure requirements,
use only belt-clips, holsters or similar accessories that do not
contain metallic components in its assembly. The use of
accessories that do not satisfy these requirements may not
comply with FCC RF exposure requirements and should be
avoided.
This device complies with Part 15 of FCC Rules and Industry
Canada licence-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this device may
not cause interference, and (2) this device must accept any
interference, including interference that may cause
undesired operation of this device.
5150-5250 MHz band is restricted to indoor operations
only.
High-power radars are allocated as primary users (i.e.
priority users) of the bands 5250-5350 MHz and 5650-5850
MHz and that these radars could cause interference and/or
damage to LE-LAN devices.
Compliance with IC requirement RSS-210 A9.4.4
Data transmission is always initiated by software, which is
the passed down through the MAC, through the digital and
analog baseband, and finally to the RF chip. Several special
packets are initiated by the MAC. These are the only ways
the digital baseband portion will turn on the RF transmitter,
which it then turns off at the end of the packet. Therefore,
the transmitter will be on only while one of the
aforementioned packets is being transmitted. In other
words, this device automatically discontinue transmission
in case of either absence of information to transmit or
operational failure.
5
.
English
