1-10-3
E9A80FIS
If an error occurs during the timer recording, one of the following error numbers (40 to 42) or the above error
messages (error number: 1 to 39) is displayed on the recording menu after timer recording.
(Once the timer programming list with error indication is displayed, the program line(s) with error will be cleared
only after the programs are cancelled and reset to the timer standby mode.)
(In the case of the error occurs during setting the timer programming, no error messages is displayed.)
This program is not allowed to
be recorded on this disc.
Insert a ver.1.1 CPRM
compatible DVD-RW disc.
28
During the CGMS picture (possible to
record once) input. (Disc which is not for
the correspondence to VR Format
CPRM)
12
This disc is protected and not
recordable.
Release the disc protect
setting in the Disc Setting
menu.
29
Disc Protected Disc.
7
Disc is full.
(No area for new recording)
Insert the recordable disc with
enough recording space.
30
No avilable recording space.
5
You cannot record more than
99 titles on one disc.
(The maximum is 99.)
Delete unnecessary titles.
31
Its recording capacity has been reached.
(Video Format Disc)
7
32
Its recording capacity has been reached.
(VR Format Disc)
8
You cannot record more than
999 chapters on one disc.
(The maximum is 999.)
Delete unnecessary chapter
markers.
33
The 999 chapter has been reached. (VR
Format Disc)
9
You cannot record on this disc
as Control Information is full.
Delete unnecessary titles.
34
There is not space to record field of
control information.
10
You cannot record on the disc
as Power Calibration Area is
full.
Insert a new disc.
35
PCA is Full. (in REC start)
4
This disc is already finalized.
Release the finalizing for this
disc.
36
It is finalized. (Video Format Disc)
6
Can not record on this disc.
Repeat the same operation.
37
Access to Memory Area range outside.
-
38
Sector Address is wrong.
-
39
BUP writing error of chapter editing.
-
Message
Solution
Error
No.
Error Description
Priority
Error message is not
displayed.
- Set the timer programming
correctly.
- Set the timer programming
before the start time.
- Insert a recordable videotape
with a record tab.
40
- Some portion has not been recorded
because of program overlapping.
- Recording did not start at the start time.
- No Videotape is inserted.
Videotape ran out during recording.
-
Turn the power on and set the
clock correctly then set timer
programming again.
41
Power failed
-
Insert the recordable disc.
42
No disc when recording
-
Message
Solution
Error
No.
Error Description
Priority
Timer Programming
2. ---
3. ---
4. ---
5. ---
6. ---
7. ---
8. ---
*
JAN/01 12:57AM 1:57AM 8 DVD
E40
VCR DVD
A program with the error number is grayed out and asterisked on the timer programming list.
The speed mode changes
to the error number.
Summary of Contents for MWR20V6
