EN-18
Manual (Wired)
In the following cases, select “Manual”(wired) to set each setting as necessary.
- If a network connection could not be established when the setting was “Auto”(wired).
- When instructed by your Internet service provider to make specific settings in accordance with your network
environment.
1. Use
[
Í
/
Æ
]
to select “Network Setup” in the home menu, then press
[OK]
.
2. At “IP Mode”, press
[OK]
, and set it to “Manual”, then press
[OK]
.
Link Status
:Link Up
MAC Address
:XX:XX:XX:XX:XX
IP Mode
:Manual
IP Address
:XX:XX:XX:XX:XX
Subnet Mask
:XX:XX:XX:XX:XX
Default Gateway :XX:XX:XX:XX:XX
Primary DNS
:XX:XX:XX:XX:XX
Secondary DNS
:XX:XX:XX:XX:XX
Wired IP Settings
.
.
.
Cancel
Network Test
Apply
Please choose a new IP Mode value
Manual
Auto
3. Use
[
Î
/
ï
]
to select “IP Address”, then press
[OK]
.
4. The IP address setting screen will appear. Enter an IP address using
[
Î
/
ï
/
Í
/
Æ
]
on the software keyboard,
then select “Done”, then press
[OK]
.
Link Status
:Link Up
MAC Address
:XX:XX:XX:XX:XX
IP Mode
:Manual
IP Address
:XX:XX:XX:XX:XX
Subnet Mask
:XX:XX:XX:XX:XX
Default Gateway :XX:XX:XX:XX:XX
Primary DNS
:XX:XX:XX:XX:XX
Secondary DNS
:XX:XX:XX:XX:XX
Wired IP Settings
Please enter a new IP Address.
Valid range of each segment is 0 to 225.
Current Value xxx.xxx.x.xxx
New Value
.
.
.
Cancel
Network Test
Apply
1 2 3 4 5 6 7 8 9 0
a
s
d
f
g h
j
k
l
;
z x
Space
c
v b n m ,
.
/
-
=
\
[
]
'
`
q
Done
w e
r
y u
o p
• The software keyboard shows up by pressing
[OK]
on the remote while in a number cell.
• When inputting a single character using the software keyboard as soon as you press
[OK]
on the remote to
input that character, then the character is displayed for a very short time to allow you to confirm that this was
the correct character.
• Enter an IP address after checking the specifications of your router.
• If an IP address is unknown, check the IP address of other devices (e.g. PC connected with a LAN cable).
Then, in the furthest cell to the right, assign a different number from those other devices.
5. Use
[
Î
/
ï
]
to select “OK”, then press
[OK]
.
6. Repeat the same procedure as steps 4 to 5 for “Subnet Mask”, “Default Gateway”, “Primary DNS” and
“Secondary DNS”.
• Enter the DNS addresses provided by your Internet provider.
• If the DNS address is unknown, check the DNS address of other devices (e.g. PC connected with a LAN
cable) and assign the same DNS address.
7. Use
[
Î
/
ï
/
Í
/
Æ
]
to select “Apply”, then press
[OK]
.
• The unit will start a network test, and the test result will appear right after the test finishes.
8. If the network test passes, press
[OK]
to exit.
Continued on next page.
X6060UD̲TB600MG2F̲F7̲OM̲EN̲WEB̲v1̲AppChannel削除版̲0711.indd 18
X6060UD̲TB600MG2F̲F7̲OM̲EN̲WEB̲v1̲AppChannel削除版̲0711.indd 18
2011/07/15 13:24:06
2011/07/15 13:24:06
