background image

2

UNPACKING

Unpack the instrument carefully. Make sure all components
have been removed from the foam protection. Inspect all
components for damage. Report any concealed damage to
the carrier within 24 hours. Check the contents of the car-
ton/crates against the packing slip and report any discrep-
ancies to Magnetrol. Check the nameplate model number
(Model number/approvals as per inserted separate sheet) to
be sure it agrees with the packing slip and purchase order.
Check and record the serial number for future reference
when ordering parts.

MOUNTING

Tri-Clamp

®

16 AMP connection

Varivent

®

connection

Threaded G1A connection

Welded flange ANSI/DIN connection

These units are in compliance with:

1. The EMC directive 89/336/EEC. The units have been tested to

EN 61326.

2. Directive 94/9/EC (ATEX 95A) for equipment or protective system intended

for use in potentially explosive atmospheres. EC-type examination certifi-
cate ISSeP06ATEX008 - explosion proof.

3. The PED Directive 97/23/EC (pressure equipment directive). Safety accessories per category IV

module H1.

Nameplate:
- part number
- serial n°

High alarm

High alarm

High alarm

Low alarm

Filling line

Pump protection

Pump

Low alarm

Max pressure: metal transducer: 138 bar (2000 PSIG)

plastic transducer: 19 bar (275 PSIG)

Ambient temperature: -25°C (-13°F) to +70°C (+160°F)

Max temp: metal transducer: +165 °C (+325 °F)

plastic transducer: +120 °C (+250 °F)

Min temp: -80 °C (-110 °F)

Summary of Contents for ECHOTEL 960













Reviews: