background image

© 

2010 Magnum Energy, Inc

.

Disclaimer of Liability

The use of this manual and the conditions or methods of installation, 

operation, use, and maintenance of the MM-R and MM-RC Remote 

Controls are beyond the control of Magnum Energy, Inc. Therefore, 

this company assumes no responsibility and expressly disclaims 

any liability for loss, damage, or expense whether direct, indirect, 

consequential, or incidental that may arise out of or be in anyway 

connected with such installation, operation, use, or maintenance.
Due to continuous improvements and product updates, the images 

shown in this manual may not exactly match the unit purchased.

Restrictions on Use

The MM-R and MM-RC Remote Controls shall not be used in 

connection with life support systems, life saving or other medical 

equipment or devices. Use at your own risk.

Contact Information

Magnum Energy, Inc.

2211 West Casino Rd.

Everett, WA 98204

phone: (425) 353-8833/fax: (425) 353-8390

web: www.magnumenergy.com

Product Safety Instructions

Read and follow all instructions and safety information contained in 

this manual before installing or using this product.

• All electrical work must be performed in accordance with local, 

state, and federal electrical codes.
• This product is designed for indoor/compartment installation. It 

must not be exposed to rain, snow, moisture, or liquids of any type.
• Use insulated tools to reduce the chance of electrical shock or ac-

cidental short circuits.
• Always verify proper wiring prior to connecting the remote.

Safety Symbols

To reduce the risk of electrical shock, 

fi

 re, or other safety hazard, 

the following safety symbols have been placed throughout this 

manual to indicate dangerous and important safety instructions.

WARNING:

 Indicates that failure to take a speci

fi

 ed 

action could result in physical harm to the user.

CAUTION:

 This symbol indicates that failure to 

take a speci

fi

 ed action could result in damage to the 

equipment.

Info:

 This symbol indicates information that emphasizes 

or supplements important points of the main text.

i

Summary of Contents for M-RC

















Reviews: