Magnum 3005 Instruction Manual Download | Manualshive

Page: 2 / 12

background image

CONTENTS

CONTENTS

FEATURES................................................................................................................ 1
GENERAL INFORMATION................................................................................. 2
ACCESSORIES....................................................................................................... 2
SAFETY..................................................................................................................... 2
STARTUP................................................................................................................. 3
SETTINGS................................................................................................................ 3
REMOVING QFP/SOP........................................................................................... 4
REMOVING PLCC.................................................................................................. 5
SOLDERING IRON................................................................................................. 5
ACCESSORIES....................................................................................................... 6
PCU CONFIGURATION........................................................................................ 6
STATION CONFIGURATION............................................................................... 7
PCCU CALIBRATION........................................................................................... 8
3005 STATION CALIBRATION......................................................................... 9
SPECIFICATIONS................................................................................................ 10

ABBREVIATIONS

PCB

Printed Circuit Board

SMD

Surface Mount Device

PCU

Portable Configuration Unit

PCCU

Portable Configuration and Calibration Unit

TERMINOLOGY

Reset PCU

Switch unit off then on.

Reset PCCU

Switch unit off then on.

Reset Station

Switch unit off then on.

Configuring

Transfer parameters from one device to another

Calibrating

Correcting measurements against a known accurate

source

Calibrating Jigs

Jigs into which the soldering iron and hot air pencil

are inserted so the temperature can be measured for calibration purposes

file:///C|/Documents%20and%20Settings/Lauren/...ther%20stuff/magnum/3005%20word%20booklet.htm (2 of 12) [03/03/2003 10:16:31 PM]

«
1
2
3
4
...
»

Summary of Contents for 3005













Reviews:

No comments

Related manuals for 3005

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands