background image

17

1.

MAIN CIRCUIT BREAKER:

 This breaker will disconnect power to the connection lugs (items 10-11). It WILL 

NOT disconnect power to the convenience outlets when the engine is running.

2.

MAGNUM DIGITAL CONTROLLER (MDC): 

Refer to 

“Magnum Digital Controller (MDC)” on page 18

 .

3.

AUXILLIARY LIGHT SWITCHES (OPTIONAL):

 These switches operate the control panel and interior lights.

4.

DIESEL EXHAUST FILTER CLEANING SWITCH:

 This switch toggles between enabling and disabling the auto 

exhaust cleaning feature and entering manual regeneration. Refer to page 

“Exhaust Filter Cleaning Operations” 

on page 28

.

5.

20A CIRCUIT BREAKERS (2):

 Circuit breakters for the 120V GFCI outlets.

6.

120V GFCI DUPLEX CONVENIENCE OUTLETS (2): 

Outlets for additional equipment that may require Ground 

Fault Circuit Interrupt (GFCI) protection.

7.

50A CIRCUIT BREAKERS (2):

 Circuit breakters for the 120/240V twist-lock outlets.

8.

REMOTE START TERMINAL BLOCK:

 Used to connect the generator to a dry-contact closure switch for remote 

starting of the generator.

9.

120/240V TWIST-LOCK CONVENIENCE OUTLETS (3): 

These outlets are used for connecting additional loads 

or equipment to the generator in 240 and 208 voltage selections only.

10.

GENERATOR GROUND CONNECTION LUG: 

This lug is for connecting a good earthen ground per local, state 

or National Electric Code (NEC) guidelines before starting the generator.

11.

GENERATOR OUTPUT CONNECTION LUGS: 

These lugs allow appropriate loads to be wired directly to the 

generator.

12.

DOOR SAFETY SWITCHES:

 The connection lug door is equipped with safety interlock switches that will trip 

the main circuit breaker and disable the voltage regulator if the door is opened while the unit is operating.

Summary of Contents for MMG100D

























































Reviews: