Accessing the Reader
Remove from Counter
In order to access the reader from
the device stand you may need
to unscrew it from the counter.
Unscrew the two screws attaching the
baseplate of the stand to the counter.
Remove Base Plate from Stand
Unscrew the two set screws from the
base plate.
Remove USB-C Cable
Unplug the USB-C cable from the
back of the device, release the cable
from pinch fit opening, and remove
from the integral cable hooks.
Remove 4 Set Screws
Unscrew the 4 screws that attach the
stand to the reader.
Underside of Device
Form Factor:
of DynaProx and
DynaProx BCR are the same smooth
form factor with 4 threaded screw
holes, a USB-C receptacle, RS-232
receptacle, and product label.
Product Label:
located on the
underside of the device. The Serial
Number, Rev, Date, Part number
(PN), and Hardware PN (HW) are
listed. Compare hardware ID to PCI
website for validation.
USB-C Connection:
Connected
directly to the correct host USB port.
Imprints:
in the plastic form factor
of certification logos and patent
information are listed.
RS-232 Connection:
Connected
directly to the correct host port.
EMV® is a registered trademark in the U.S. and other countries and an unregistered trademark elsewhere. The EMV trademark is owned by EMVCo, LLC. The Contactless Indicator mark, consisting of four graduating arcs, is a trademark owned by and used with permission of EMVCo, LLC.
Registered to ISO 9001:2015 © Copyright 2022 MagTek, Inc. PN D998200542 rev. 20 7/22
MagTek
®
Inc., 1710 Apollo Court, Seal Beach CA 90740 | p 562-546-6400 | support 651-415-6800 | f 562-546-6301 | www.magtek.com
D
C
B
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
A
SHEET 1 OF 1
DESIGNED BY
DO NOT SCALE DRAWING
DRAWN BY
TOLERANCE:
TITLE:
B
SIZE
PROPRIETARY AND CONFIDENTIAL
FINISH:
4.00 x 2.8265”
DWG REV :
CHECKED BY:
DATE
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MAGTEK. ANY REPRODUCTION IN PART
OR AS A WHOLE WITHOUT THE WRITTEN
PERMISSION OF MAGTEK IS PROHIBITED.
SCALE: 1:1
MUST BE ROHS COMPLIANT, SEE
EUROPEAN DIRECTIVE 2002/95/EC
DIM UNITS:
DWG NO.
MATERIAL:
PART NO.
1/10/2022
R.Robinson
R.Robinson
DynaProx & DynaProx BCR
EMV and NFC Contactless
DynaProx STORAGE NOTICE
TEMPERATURE:
-30°C to +85°C (-22°F to 185°F)
HUMIDITY:
90% RH non-condensing
DynaProx BCR STORAGE NOTICE
TEMPERATURE:
-40°C to +70°C (-40°F to 158°F)
HUMIDITY:
5 - 95% non-condensing
See product label for part number and description.
In-house Zebra label
PN 99600120
LABEL, STORAGE NOTICE, DYNAPROX
AND DYNAPROX BCR
1000008550
D100006015
B0
DynaProx and DynaProx BCR Stand | Device Inspection
Include the following for your device inspection audit:
•
Be certain to have a list of the devices and include the details listed on the
product label.
•
It may be helpful to take photos of the top, back, and side of each device.
Be certain to check device part numbers, serial numbers and IDs and check
physical connections. Use the chart below as a checklist to inspect the device
for signs of tampering.
Are there signs of tampering:
Signs of tampering
Site Inspection
YES
NO
Form Factor - check overall form factor
Top
Contactless Landing Zone
LEDs
Barcode Reader Camera
Front, Left, and Right Sides
Plastic Shell
Form Factor
Cables
USB-C Cable
Bottom and Back
Form Factor
Cable Connection
Screw Sets
User should report all signs of tampering as per standard protocol.
NOTICE:
If there is forced entry, the security switches built into the electronics
will be tampered. If they are tampered the sensitive data such as encryption
keys and certificates are cleared as part of security measures mandated by
PCI and the device will not be available to make transactions. If the device has
detected a tamper, DynaFlex Products cannot be repaired in the field. Follow
RMA procedures. Devices must be returned to the factory for repair.
PCI DEVICE VALIDATION
To check for PCI Validation check the Hardware and Firmware ID. Hardware ID
is printed on the label. The firmware ID is accessible via a host command and is
displayed. Go to the PCI compliance web page and search for MagTek, and find
the product name, DynaFlex. Compare the Hardware ID and Firmware ID:
https://www.pcisecuritystandards.org/assessors_and_solutions/pin_transaction_devices
Device Inspection
Access Inspection - Views from Stand Bottom
Full Assembly
Diagram shows assembly pieces.
•
2-set screws
•
Base plate
•
4 mounting screws
•
Angled stand and cable
•
DynaProx product
