M A G U I R E P R O D U C T S , I N C .
Edition: August 5, 2014
37
W E I G H S C A L E B L E N D E R
®
Menu Map – Brief Explanation
Main Screen
►
Options
(password protected) – Settings and Options Menus
►
Parameters
– Controller Operation Parameters
Control Times – DLY, DTI, STL , SBO
Vibration Control – KDF, WDF, BER
Weight Limits – FUL, MAX, TH, TL
Components (12) – RP, RD, AL, LA, WT, TI, PO, SE, XT, NC
Regrind Control – ROC, ROV, RHL
Mixer Control – MIX, JOG, MPO, FCV
►
Special Functions
– Initial setup options, diagnostics, print outs
►
Setup
– Basic setup options
Select Mode of Operation - Standard, Dispense, totalizer, Extrusion
Setup Date and Time – Current Data and Time for logs
Component Type Selection – Set hoppers to REG, NAT, ADD or Off.
Weight Unit for Reports – Pounds or Kilograms
Blender I.D. – Blender ID for Communications and logs
Calibrate
Load
Cells
Language
►
Diagnostics
– functions for troubleshooting
Volumetric Operation – Timed operation
Factory Access - For factory access only
System
Information
TCPIP
Diagnostics
Load Cell Diagnostics
Screen Saver Setup – Enable screensaver function to prevent screen burn.
►
Print Options
– Sends printouts to USB drive
Print Diagnostics – Diagnostics printout of cycle by cycle and/or print timed totals
output in minutes
Print Parameters – Prints parameters table
Document Weights - Prints weight on display, date & time to a USB drive
►
TCP/IP Configuration
– Setup of IP Address and related settings
►
Operating Options
– Options for blender operation
End Empty or Full – End Cycle with bin Empty or the bin Full
Precision Ratio – Toggle Precision Ratio On / Off for specific components
Dispense Order - Specify dispense order of active components (All regrind).
Progressive Metering – Enable / disable Progressive Metering
Close Weigh Bin Operate Twice – Toggle weigh bin close once or twice
►
Special Features
– Special Blender Operation Options
Enable Special Operations – Enables / disables certain options
Special Alarm Conditions – Enables specific alarm conditions
►
Resets
– Reset Blender
Clear Totals – Resets totals
Save/Restore Settings – Saves and restores WSB settings
Change Passwords – Set Passwords Manual, Program Mode, Thumbwheel
Software Updates – Apply software updates to the controller via USB
►
Manual Operation
– Manual testing of Blender functions
►
Timed Operation
– Setting Timed operation of components
►
Calibrate Flow Rate
– Calibrating Flow Rate per component
►
View
– Displays current and accumulated information about the Blender
►
>>
- Displays additional components (maximum 6 components on screen)
►
Printer
is On/Printer is Off – Enables / disables USB print output
►
STOP/START
– Starts / Stops the blender cycles
Summary of Contents for Weigh Scale Blender WSB
