M A G U I R E P R O D U C T S , I N C .
Edition: August 6, 2014
38
W E I G H S C A L E B L E N D E R
®
Menu Map – Full Explanation
Main Screen
Options (password protected) – Options are accessible from the main screen by pressing
“Options”. Enter password (22222 by default). Press “Parameters”.
Parameters –
All WEIGH SCALE BLENDER controllers operate according to certain internal PARAMETERS.
Because customer requirements vary widely, we have made a wide range of parameters accessible for change
through the touchscreen. Parameters are grouped into the following categories: Control Times, Vibration Control,
Weight Limits, Components, Regrind Control, Mixer Control. Parameters are covered on page 45.
Special Functions
Setup - Basic setup options
Select Mode of Operation –
Selects the mode of operation. Choices are Standard -
Blender, Dispenser Mode, Totalizer Mode, Extrusion Control Mode.
Setup Date and Time –
Allows the user to set the month, day, year, hour and minute of
the Touchscreen controller.
Component Type Selection –
Allow manual selection of component types (Type Regrind,
Natural or Additive) or OFF (turns off the component). See Turning on Material Type
Outputs on page 26.
Weight Unit for Reports -
Select Weight Units for report output by selecting the desired
weight unit (KILOGRAMS or POUNDS) for readout of data. For the U.S.A. systems are
supplied with POUND readout selected. KILOGRAMS are preferred for nearly all countries
outside the U.S.A.
Blender I.D. -
Sets the Blender ID number. Enter an identification number for this
particular weigh scale blender. This I.D. number will appear on all printed reports. If you
have more than one unit, this helps to identify reports. If you are using a computer to
automatically gather data, then each controller must have a unique address. Valid
numbers are 000 to 255. When connected to a computer, do not use the number 000 or
255 for identification. Enter the ID number by using the keypad, then click save. Press Exit
when complete.
Calibrate Load Cells –
Routine for performing a Zero Weight Calibration and a Full
Weight Calibration. See “Load Cell Recalibration” on page
80.
Diagnostics –
Option for Diagnostics and Testing
Volumetric Operation –
Used to put the controller in Volumetric Mode. ENABLED (ON) or
DISABLED (OFF). Press EXIT when done. When power is turned off this flag is always
reset to OFF. With this flag ENABLED (VOLUMETRIC operation ON), the load cells are
completely ignored. Error correction and rate recalibration does not take place. The unit
functions like a volumetric feeder without checking or correcting for errors. Since load cell
readings are ignored, this flag allows operation even if the load cells become damaged.
Summary of Contents for Weigh Scale Blender WSB
