M A G U I R E P R O D U C T S , I N C .
Edition: August 5, 2014
39
W E I G H S C A L E B L E N D E R
®
Dispense times will be based entirely on the WT and TI parameters.
Factory Access –
For factory access only.
System Information –
System Information displays the following information: Software
version, serial number, build version, power board firmware version, WSB model, IO Type,
Config version, last loaded software version, time and date, WSB ID#, IP address, subnet
mask, TCP port, WTD.
TCPIP Diagnostics –
TCP diagnostics provides an array of Ethernet diagnostics
information.
Load Cell Diagnostics –
Load cell diagnostics provides raw feedback from the load cells.
Screen Saver Setup –
Screen saver setup allows a screen saver to be enabled/disabled
and a time for the screen saver to be activated. When enabled, the screen saver will only
activate if the time selected elapses after no user feedback and when the controller is
displaying the main screen. During an active screen saver, the moving display will show
the actual weight.
Print Options –
Used for Printouts
Print Diagnostics –
Cycle-by-Cycle Printout. Select “Print Diagnostics” to set flag for a
printout of data after each full dispense cycle. With this flag ENABLED and with a USB
Flash Drive in the USB port, four lines of information about the dispense cycle that just
occurred will be sent to the printer. Press “Print Diagnostics” to toggle between ENABLED
(Bullet ON) and DISABLED (Bullet OFF). A file will be created on the USB drive called
print.txt. The information in this file includes dispense weight and percentage of each
component, the internal rate numbers used by the computer to determine dispense time,
and the actual dispense time of each component. This is excellent information to track the
accuracy of each dispense cycle and the accuracy of the entire system over an extended
period of time. Select “Print material totals every 2 minutes” to add material totals to the
file.
Print Parameters –
Parameter Printout. Press “PRINT” to print a file called parameters.txt
to a USB Flash drive. This file will contain all internal parameters. A USB flash drive must
be plugged into the USB drive. Up to 13 lists will print, a General list and 12 component
lists. Only components that are turned "on" will print. A Summary of the Blender will print
followed by five columns, the parameter name, Factory, User, Saved and Current. Also
printed is Model, software version, Special Features (on or off), Functions (on or off),
Progressive metering state and device, as well as _PT percent.
Document Weights –
Press “Print” force a printout of the displayed weight on the
controller. A USB flash drive must be plugged into the USB drive. DATE, TIME, Machine
number, and display will print:
Date:
11/09/2008
Time:
17:22:01
Machine number: 002
Display Readout: 500.0
Summary of Contents for Weigh Scale Blender WSB
