M A G U I R E P R O D U C T S , I N C .
Edition: August 6, 2014
40
W E I G H S C A L E B L E N D E R
®
This is useful for obtaining printed verification of load cell accuracy for ISO and other
international quality program rules.
The recommended procedure is:
1.
Place the unit into the Program mode (press OPTIONS).
2.
Press Special Functions, Print Options, Document Weight, then press the “Print”
button for printout of empty bin TARE weight.
3.
Place a KNOWN CERTIFIED WEIGHT into the weight bin.
4.
Press “Print” again for printout with the weight added.
5.
The different between the two weight printouts should equal the KNOWN
CERTIFIED WEIGHT.
TCP/IP Configuration –
Configure controller IP Address, Subnet, Default Gateway, Remote IP,
Local Port and Host Port. Communications are used specifically for MLAN (Maguire Local Area
Network) Protocol communications. For more, see Communications on page 23.
Operating Options –
Special Operating Options
End Empty or Full -
END the Cycle with: BIN EMPTY (standard), or BIN FULL
This flag for SPECIAL APPLICATIONS ONLY. Select Standard: end with bin empty or
select Option: end with bin full to tell the controller to end a cycle when the weigh bin is
EMPTY or end with the bin FULL. The BIN FULL option is only for special installations
where the sensor has been relocated BELOW the mix chamber and the instructions to do
otherwise.
Precision Ratio –
Precision Ratioing for Additives
Select this option to produce a precision ratioing of a selected Additive. Press the
displayed Component (MAT 3, MAT 4, etc) to toggle between PRECISION RATIOING
OFF, PRECISION RATIO Material 1 ON, PRECISION RATIO Material 2 ON, etc. Only
those components already designated as an ADDITIVE will be displayed. If precision
rationing is selected, the specified additive will dispense BEFORE the Naturals, instead of
after. Natural dispenses occur after the selected additive dispense and are calculated to
assure the most exact percentage ratio for the selected component. Because the Natural
dispenses are larger, this method allows for more exact ratioing of the one selected critical
component.
Dispense Order
- For recipes containing all regrind type components. Specify the
dispense order of active regrind components. Select the components by selecting them in
the order that they should be dispensed. Dispense order will display above. Clear will
remove dispense order. New recipes will inherit dispense order. Internally saved recipes
will save the dispense order.
Progressive Metering –
Progressive Metering allows for more accurate dispenses of
selected components. However, cycle time will be extended by a few additional seconds.
In normal operation blenders target a dispense of the full requested amount in one try.
This almost always works, and generally will fall within acceptable upper and lower error
limits. Making the dispense in one try allows for high throughput rates while still achieving
a level of accuracy acceptable for most processors. When the accuracy of one particular
component is critical, or the process depends on maintaining a tighter tolerance of this
Summary of Contents for Weigh Scale Blender WSB
