M A G U I R E P R O D U C T S , I N C .
Edition: August 5, 2014
47
W E I G H S C A L E B L E N D E R
®
BER 01000
BAIL-OUT THRESHOLD - Excess GRAM weight before dispense is aborted.
This parameter controls sensitivity of the emergency "bailout" routine that prevents overfilling of the
weigh bin. No change is required.
FUL 20000
FULL BIN WEIGHT - determined by weigh bin size.
MAX 30000
Maximum BIN WEIGHT - weight the software will target (grams).
FUL is the target weight that is blended each cycle. Change only for extremely fluffy or very heavy
material. MAX prevents overflowing of the weigh bin. It is reset automatically if the FUL parameter is
changed.
TH 01000
VALID TARE WEIGHT HIGH - The highest acceptable TARE weights for Blend cycle to start.
TL 00500
VALID TARE WEIGHT LOW - The lowest acceptable TARE weights for Blend cycle to start.
TL prevents starting with the weigh bin out of place. No change is required.
TH prevents starting with a full weigh bin. Change TH only if clumps of material hang up in the weigh
bin.
ROC 00000
REGRIND OVERCOLOR - ROC, ROV, and RHL help control regrind usage.
ROC indicates the PERCENT of REGRIND that will be treated as natural when COLOR and
ADDITIVE dispenses are calculated. This adds some color or additive to your regrind.
ROV 00000
REGRIND OVERRIDE -
ROV is for closed loop fully automatic reprocessing of regrind scrap. This
parameter will detect when more regrind is being produced than consumed, and override the current
setting to use a higher amount. This helps prevent material backing up in your grinder.
RHL 00000
REGRIND LEVELS – HI/LOW -
RHL has effect only if level sensors are added to your unit to detect
material level in the regrind hopper. These level sensors can alter regrind percent usage.
MIX 00015
MIXER MOTOR TIME
This parameter times how long the MIX motor runs.
JOG 03030
MIXER MOTOR JOGGING, COUNTS and TIME
JOG indicates the number of times the blade will jog after initial mixing is ended, plus the time interval
between these jogs.
MPO 00000
For air drive reciprocating mix motor
FCV 00006
FLOW CONTROL DELAY - TIME the Flow Control valve delays before opening (Seconds).
This parameter holds each batch in the mix chamber for a time to assure mixing. This is only for units
equipped with the optional flow control valve under the mix chamber.
PRT 00000
REPORT INTERVAL - MINUTE interval between automatic print of TOTALS.
This parameter will cause your system to PRINT MATERIAL TOTALS automatically. A USB Flash
Drive must be connected. This parameter is located under Options / Special Functions / Print Options
/ Print Diagnostics.
Summary of Contents for Weigh Scale Blender WSB
