M A G U I R E P R O D U C T S , I N C .
Edition: August 5, 2014
79
W E I G H S C A L E B L E N D E R
®
Turning on Cycle by Cycle Printing:
Press
OPTIONS
Display will say:
ENTER PASSWORD
Press
then, press Enter
Display will show menu options
Press
SPECIAL FUNCTIONS
Display will show menu options
Press
PRINT OPTIONS
Display will show the menu options: Print Diagnostics and
Print material totals every 60 minutes.
Press
Print Diagnostics
Radio Button will toggle on/off with each press. Toggle this
so that it is selected.
Press
Four times
To return to the Main Screen.
Be sure to insert a USB drive into one of the two USB ports on the right side of the controller.
Press
to toggle On
Button will display the Printer is On
To turn off printing, press the Printer is
On button to toggle it off.
A floating, drifting number usually indicates the load cells are not plugged in.
A readout of 0 indicates an open circuit, a damaged wire or cell.
A full-scale readout of 249,850 indicates a damaged wire or cell.
A set of 3 K load cells will put out about 33 more counts for every gram of weight that is added. A test of sensitivity is to add a
small weight to the bin. The RAW WEIGHT count should increase by about 33 counts for each gram added. (10 counts per gram
for 10K load cells.)
If you call us for help in solving a load cell problem, it is helpful if you can tell us what the RAW COUNT number is with the bin
empty, and with a known weight in it. Pressing the CE key at any time will display the RAW COUNT number for the current
weight.
To OPERATE with DAMAGED load cells in a VOLUMETRIC mode see OPTIONS, Special Functions, Diagnostics, Volumetric
Operation.
Backup, Restore, Factory Reset
Locations of stored Blender settings and their purpose
There are 3 memory areas where Blender settings are stored. These options are accessible by pressing
OPTIONS, Special Functions, Resets, Save/Restore Settings.
1.
Restore User Settings
- The current settings in use. When you make parameter changes and/or enable
features, the changes (if any) are recorded into the user-settings when you exit OPTIONS mode. When
changes are made to User Settings, the changes are stored in EEPROM memory so that they are not lost
when the Blender is powered off.
2.
Save User Settings
– The area in memory where User Settings are backed up into when the “Save User
Settings” function is used. If User Setting were never backed up using “Save User Settings” function then
Factory default settings reside in this memory location. If they were previously backed up, User Settings
can be restored into “User Settings” using the Restore User Settings function.
3.
Load Factory Settings
- The area in memory that holds the Blender's factory default settings. The
Factory Default Settings are hard-coded default settings for each model. Factory Default Setting can be
restored using the “Load Factory Settings” function.
Summary of Contents for Weigh Scale Blender WSB
