background image

© MAHLE 

Important notes  |  ACX2120H  |  7

en

 

The ACX2120H must always be transported in its operating 

position. Never lay the ACX2120H on its side, as oil could 

then escape from the vacuum pump or the built in compres -

sor could be damaged.

There are no additional safety systems for protecting the 

ACX2120H against damage resulting from natural catastro -

phes.

 

Never remove any components from inside the ACX2120H 

except for maintenance or repair purposes.

 

Follow the pertinent legal regulations or directives to ensure 

safe handling of pressurized devices.

 

We recommend calibrating the scales at least once per year. 

Contact customer service for calibration of the scales.

 

The ACX2120H must be subjected to regular maintenance by 

service personnel or authorized agents to ensure the safety 

of the unit.

 

Disconnect power before performing any maintenance or 

service to unit.

 

Never perform any maintenance work which is not expressly 

recommended in this manual. Contact customer service if 

components have to be replaced other than in the course of 

maintenance work.

 

ACX2120H must be connected to a properly grounded electri -

cal connection.

 

If there is damage to the ACX2120H, terminate usage imme -

diately and contact customer service.

 

The service hoses and service quick-release couplings must 

be regularly checked for wear and replaced if damaged.

 

The ACX2120H must be operated in an environment cor-

responding to the directive BGR 157 with respect to the 

exchange of air.

 

Observe local laws or directives as to ensure the safety of the 

pressurized device.

 

For safety reasons it is advisable to use a residual current 

operated circuit breaker (r

-

tions:

Parameters

Rated voltage

110 VAC ± 10%

Rated frequency

50/60Hz

Rated current

10A

Rated tripping current

30mA

Tripping switch

C

2.5

 

Safety devices

Description

Function

Pressure switch

Switches the compressor 

 if the normal operat -

ing pressure is exceeded.

Safety valve

The safety valve opens if the design pressure is ex -
ceeded.

Circuit breaker

Interrupts the power supply if overcurrent is applied 
to the  ACX2120H .

Vents

The  ACX2120H  is provided with vents in the bottom 
of the housing to ensure the exchange of air even 

Summary of Contents for ArcticPRO ACX2120H









































Reviews: