7
Mahr GmbH, MarSurf PS 10
Taster einmessen
1. Das Normal
(11)
an der Unterseite des
MarSurf PS 10 mit dem Fingernagel anhe-
ben und herausnehmen
(s. Abb. 1)
.
2. Den
Rz
-Sollwert vom Normal ablesen.
3. Das MarSurf PS 10 auf seine prismatische
Unter seite stellen, so dass die Tastspitze
senkrecht steht.
4. Das Normal so platzieren, dass die gesam-
te Taststrecke innerhalb des Fel des mit der
defi nierten Rauheit liegt
(s. Abb. 3)
.
Die Länge der Taststrecke wird
auto
matisch gemäß DIN
EN
ISO 4288 bzw. ASME B46.1 in Ab-
hän
gig
keit vom Sollwert ermittelt
(s. mit ge lieferte Faltkarte "MarSurf.
Ober flächen-Kenngrößen").
Dazu
ad
diert sich ein halber Vor- und
Nach lauf.
5. Die Höhen ein stellung
(7)
am MarSurf PS 10
auf die nötige Höhe einstellen:
−
beim Standardtaster PHT 6-350 auf ,
−
bei anderen Tastern nach Bedarf.
Der Taster muss parallel zum Normal ausge-
richtet sein.
6. In der Grundansicht die Taste
antippen
(oder im Menü den Eintrag
Einmessen
an-
tippen).
7. Das Einmessverfahren auswählen.
Bei Verwendung des mitgelieferten Normals
immer "Einmessen Rz" auswählen.
8. Den Sollwert des Normals in das Feld "Soll-
wert" eingeben.
9. Die Taste
Einmessen starten
antippen.
Es werden automatisch drei Messungen
durch geführt.
10. Nach der 3. Messung wird aus den drei ge-
messenen Werten (
Rz
,
Ra
oder
RSm
) ein
Korrekturwert berechnet.
i
3
Erste Schritte
Sobald folgende Schritte durchgeführt worden
sind, kann man mit den Messungen starten:
−
Transportsicherung entfernen
−
Vorschubgerät in das MarSurf PS 10 einset-
zen (s.
in Kap. 4)
−
Messbedingungen einstellen
−
Taster einmessen
Transportsicherung entfernen
Bevor das MarSurf PS 10 in Betrieb ge-
nommen wird, muss die rote Trans port-
sicherung ent fernt werden (s. Hinweis-
blatt 3763316)!
Bewahren Sie die Transport siche rung un-
bedingt auf!
Bei einem eventuellen Rücktransport des
Geräts muss die Transport siche rung wie-
der aufgesetzt werden!
MarSurf PS 10 einschalten
1. Die grüne
Start
-Taste drücken.
Grundeinstellungen vornehmen
1. Im Dialog "Gratulation":
•
Die Taste
>
antippen, um nacheinan-
der die Sprache (
), das Datum und
die Uhrzeit einzustellen.
•
Die Maßeinheit "mm" oder "inch" aus-
wählen.
•
OK
antippen.
Das Menü wird angezeigt. Erneutes
Antippen von
OK
zeigt die Grund an-
sicht an.
Messbedingungen einstellen
1. In der Grundansicht die Taste
antippen
(oder im Menü den Eintrag
Mess be din-
gungen
antippen).
2. Erneut die Taste
antippen und die ge-
wünschten Messbedingungen einstellen.
Für Details zu den Messbedingungen: s.
Kap. 5.
3.
OK
antippen. Erneut
OK
antippen.
i
Summary of Contents for MarSurf PS 10
