8
Mahr GmbH, MarSurf PS 10
MarSurf PS 10 ausschalten
1. Die grüne
Start
-Taste länger als 2 s ge-
drückt halten.
Wenn das MarSurf PS 10 nicht in seinem
Trage etui verstaut wird, sollte es seitlich
ge kippt ab gelegt werden, um eventuelle
Beschädigungen der Tast spitze zu ver-
meiden.
Akku laden
Das MarSurf PS 10 wird über den eingebauten
Akku mulator mit Strom versorgt.
Bei stationärem Be trieb kann das Gerät
ge laden werden, in dem man das mitge-
lieferte Steckernetzteil über das mitge-
lieferte USB-Kabel an das MarSurf PS 10
anschließt (s. u.).
Der Akku muss geladen werden,
−
wenn das Gerät erstmalig in Betrieb ge-
nommen wird,
−
wenn seit dem letzten Aufladen ca. drei
Mo nate vergangen sind,
−
wenn in der Titelleiste das Akkusymbol
angezeigt wird (d. h. der Akku hat weniger
als 20 % seiner Ka pazität).
Zum Laden ist ausschließlich das mitge-
lieferte Steckernetzteil mit dem mitgelie-
ferten USB-Kabel zu verwenden!
Bei Verwendung anderer Netzteile be-
steht die Gefahr, dass das MarSurf PS 10
be schädigt wird, und es erlischt jeglicher
Garantieanspruch.
Bei Verwendung eines anderen USB-
Kabels kann es zu unerwünschten Effek-
ten kommen (z. B. könnte das Mar Surf
PS 10 nicht vom Computer erkannt wer-
den oder sich der Ladevorgang erheblich
verlängern).
7
7 Diese Effekte können z. B. bei einem USB-Kabel mit zu
großer Länge oder zu geringem Leitungsquerschnitt auf-
treten.
Mindestanforderungen: Querschnitt AWG24 bei einer
max. Länge von 2 m.
i
i
−
Wenn der "Korrekturwert (neu)" im
Bereich von ±15 % liegt, kann er mit
OK
in die Geräte ein stel lung übernom-
men werden.
−
Mit
Abbrechen
kann erneut der Dia-
log "Einmessen" angezeigt werden,
um den Einmessvorgang zu wieder-
holen.
−
Wenn der Korrekturwert den o. g. Be-
reich überschreitet, wird eine Fehler-
meldung angezeigt.
Abhilfe:
OK
antippen, den Messaufbau,
den Taster, die senkrechte Ausrichtung
der Tast
spitze und den eingegebe-
nen Sollwert über prüfen und das Ein-
messen wiederholen.
11. Falls mehrmalige Wiederholung des Ein mes-
sens zu kei nem brauchbaren Ergebnis führt,
ist wahrscheinlich der Taster defekt. Er sollte
ggf. zur Überprüfung ein geschickt werden.
12. Das Normal
(11)
mit der Nase in die Aus-
sparung auf der Unterseite des MarSurf
PS 10 einsetzen und einrasten.
Weitere Einstellungen vornehmen
Für Details zu den Einstellungen: s. Kap. 5.
Um die gewünschte Sprache einzustel-
len:
Im Menü den Eintrag
Grund ein stel-
lun gen
antippen, die Taste
>
neben dem
Eintrag "
Sprache" an tippen und z. B.
"Deutsch (de)" aus wählen.
Messung starten
1. Die grüne
Start
-Taste drücken.
Die Messung wird gemäß den Einstellungen
durchgeführt und ausgewertet.
i
Summary of Contents for MarSurf PS 10
