9
Mahr GmbH, MarSurf PS 10
Steckernetzteil vorbereiten:
1. Den passenden Netzadapter auswählen
und an das mitge lieferte Steckernetzteil ste-
cken.
2. Den USB-Stecker des mitge lieferten USB-
Kabels in das Steckernetzteil stecken.
Akku laden:
1. Den microUSB-Stecker des USB-Kabels an
die USB-Schnittstelle
(6)
des MarSurf
PS 10 anschließen und das Stecker netz teil in
die Netz steck dose stecken.
Während des Ladevorgangs wird in der
Titel leiste das Akkusymbol
angezeigt.
Mit angeschlossenem Stecker netz-
teil kann sofort gemessen werden.
Nach ca. 3 Stunden Ladezeit ist der Akku
geladen, und das Gerät schaltet automa-
tisch von Schnell
ladung auf Erhaltungs-
ladung um.
2. Um die erreichte Akkukapazität in % an-
zuzeigen: Das MarSurf PS 10 vom Stecker-
netzteil trennen und im Menü den Eintrag
Info
antippen.
Das MarSurf PS 10 wird auch geladen, wenn es
über seine USB-Schnittstelle
(6)
an einen
Com pu ter angeschlos sen ist.
Wenn der Computer einen speziellen USB-
Lade port hat, beträgt die Ladezeit ebenfalls ca.
3 Stunden.
Wenn der Computer jedoch einen normalen
USB-Port hat, dann verlängert sich die Ladezeit
auf ca. 6 bis 7 Stunden.
i
4
Messplatz einrichten
Mobiler Messplatz
−
Das MarSurf PS 10 kann als komplette Ein-
heit auf ebene oder zylindrische Oberflächen
auf gesetzt werden
(s. Abb. 1, oben)
.
−
Das Vorschubgerät kann aus dem MarSurf
PS 10 herausgenommen und in seinem
Prismen halter
(9)
auf ebene oder zylind-
rische Oberflächen aufgesetzt werden
(s.
Abb. 1, unten)
.
(Bitte
durchführen, s. u.)
−
Das Vorschubgerät kann im optionalen
Hand prisma (6910434) getrennt vom Aus-
werte gerät aufgestellt werden.
(Bitte
,
durchführen, s. u.)
Mit den optionalen, höheneinstellbaren
Füßen (6850720) kann das Handprisma auf
unter schiedliche Höhen eingerichtet wer-
den.
Stationärer Messplatz
−
Das MarSurf PS 10 kann als komplette Ein-
heit an einem Mess ständer MarSurf ST-D,
ST-F oder ST-G befestigt werden.
Dazu wird eine optionale Aufnahme
(6910209) benötigt.
−
Das Vorschubgerät kann im optionalen
Hand
prisma (6910434) an einem Mess-
ständer MarSurf ST-D, ST-F oder ST-G befes-
tigt werden.
Dazu wird eine optionale Auf
nahme
(6851304) benötigt.
(Bitte
,
durchführen, s. u.)
−
Das zylindrische Vorschubgerät kann an
einem Mess
ständer MarStand 815
GN
oder einer vorhandenen Haltevorrichtung
(Spann schaft-Ø 8 mm) befestigt werden.
Dazu wird eine optionale Aufnahme
(6910435) benötigt.
(Bitte
,
durchführen, s. u.)
Summary of Contents for MarSurf PS 10
