18
Mahr GmbH, MarSurf PS 10
6.1
Sprawdzanie zintegrowanego
wzorca
Aby wyznaczyć wartość
Rz
zintegrowanego
wzorca:
1. Ustawić odpowiedni chropowatościo-
mierz
9
tak, aby głowica przylegała do
zintegrowanego wzorca i mogła mierzyć
odcinek 5,6 mm
(patrz rys. 3)
.
2. Na przyrządzie pomiarowym ustawić od-
cinek odwzorowania
Lt
= 5,6 mm.
3. Wykonać jeden lub kilka pomiarów i od-
czytać każdorazowo wartość
Rz
.
4. Obliczyć średnią z uzyskanych wartości
Rz
.
5. Wprowadzić obliczoną wartość
Rz
jako
wartość nominalną
Rz
podczas kolejnej
kalibracji urządzenia MarSurf PS 10.
6.2
Wymiana akumulatora
Maksymalna pojemność wbudowanego aku-
mulatora zmniejsza się stopniowo wraz z okre-
sem używania, dlatego konieczna może być
jego wymiana.
Wymiany akumulatora może dokonać
wyłącznie wykwalifikowany personel.
Można używać wyłącznie akumulato-
rów litowo-jonowych 3,7 V/3150 mAh
(3030057). W przeciwnym razie istnieje
niebezpieczeństwo zniszczenia urządze-
nia.
Wymiana akumulatora
(patrz rys. 6 na tylnej
obwolucie)
:
1. Odkręcić i wyjąć cztery śruby
(25)
znajdują-
ce się na spodzie urządzenia MarSurf PS 10
za pomocą wkrętaka krzyżowego.
2. Postawić urządzenie MarSurf PS 10 na pry-
zmowej stronie dolnej.
9
np. mechanizm posuwowy MarSurf SD 26 z głowicą
bezślizgaczową BFW-250 oraz urządzenie analizujące
MarSurf M 400 lub MarSurf XR 1
Transport/wysyłka
Uwaga:
Mechanizm posuwowy i głowica mogą
zostać uszkodzone w transporcie lub
podczas wysyłki.
Należy bezwzględnie przestrzegać po-
niższych instrukcji dotyczących trans-
portu oraz wysyłki. W przeciwnym wy-
padku gwarancja traci ważność!
Transport na terenie zakładu w torbie:
1. Nałożyć czerwone zabezpieczenie trans-
portowe od dołu na uchwyt pryzmowy (
(9)
(patrz arkusz informacyjny 3763316).
2. Wyłączyć urządzenie MarSurf PS 10 i umie-
ścić w torbie transportowej.
Wysyłka:
1. Wyłączyć urządzenie MarSurf PS 10.
2. Wyjąć mechanizm posuwowy z urządzenia
MarSurf PS 10 (patrz
w rozdz. 4).
3. Nałożyć czerwone zabezpieczenie trans-
portowe od dołu na uchwyt pryzmowy
(9)
(patrz arkusz informacyjny 3763316).
4. Umieścić mechanizm posuwowy w przewi-
dzianej do tego celu przegródce kartonu
wysyłkowego.
5. Urządzenie MarSurf PS 10 (umieszczone
w torbie transportowej) oraz pozostałe
akcesoria zapakować do kartonu wysył-
kowego.
Summary of Contents for MarSurf PS 10
