19
Mahr GmbH, MarSurf PS 10
6.3
Установка обновлений
программного обеспечения
При обновлении программного
обеспечения все настройки,
а также
профили, результаты и протоколы
измерения, хранящиеся в памяти,
сохраняются.
Исключение:
При обновлении программного обеспече-
ния с версии v1.00-12 (или более ранней)
до версии v1.00-14 (или более поздней)
необходимо выполнить следующие дей-
ствия:
•
Перед тем как приступить к обновле-
нию, при необходимости выполните
резервное копирование данных, на-
пример, из папок
\\MarSurfPS10 \Export
\Profiles
\Records
\usersettings
•
По завершении обновления заново
выполните калибровку щупа, уста-
новленного в MarSurf PS 10 (см.
Раздел 3).
Обновление программного обеспечения
можно выполнять, только если аккуму-
лятор полностью заряжен или прибор
MarSurf PS 10 подключен к сети с помо-
щью блока питания.
Чтобы установить новую версию программного
обеспечения, выполните следующие действия:
1. Выключите прибор MarSurf PS 10.
2. Вставьте карту MicroSD с новой версией ПО
в гнездо
(5)
.
3. Включите прибор MarSurf PS 10.
Новая версия ПО будет установлена
а в т о м а т и ч е с к и , о ч е м п о я в и т с я
соответствующее сообщение.
4. Извлеките карту MicroSD из гнезда
(5)
.
i
3. Аккуратно наклоните верхнюю часть
(26)
прибора MarSurf PS 10 на 90° влево (как при
открытии книги).
4. Аккуратно отсоедините разъемы
(27)
и
(28)
от клемм
(27a)
и
(28a)
на плате.
5. Ослабьте три винта держателя аккумулятора
(30)
.
6. Извлеките аккумулятор
(29)
.
7. Вставьте новый аккумулятор (3030057)
этикеткой вверх.
8. Установите держатель аккумулятора
(30)
на
аккумулятор (надписью "Top" вверх) и затя-
ните три винта усилием 0,4 Н·м.
9. Подключите разъемы
(27)
и
(28)
к клеммам
(27a)
и
(28a)
на плате.
10. Аккуратно верните верхнюю часть прибора
MarSurf PS 10 на место.
Ч е т ы р е в и н т а я в л я ю т с я
самонарезающими, поэтому
чрезмерное усилие при их
затягивании может привести к
серьезному повреждению корпуса.
11. Установите четыре винта
(25)
на место и
затяните их
усилием, не превышающим
1 Н·м
.
12. Включите прибор MarSurf PS 10 и убедитесь,
что он работает правильно.
13. Проверьте настройки MarSurf PS 10.
14. Полностью зарядите аккумулятор MarSurf
PS 10.
Summary of Contents for MarSurf PS 10
