7
Mahr GmbH, MarSurf PS 10
Tapintó bemérése
1. Emelje meg az etalont
(11)
a MarSurf PS 10
alsó oldalán a körmével, és vegye ki
(lásd
az 1. ábrát)
.
2. Olvassa le az etalonról az
Rz
névértéket.
3. Állítsa a MarSurf PS 10 készüléket a priz-
mával ellátott alsó oldalára úgy, hogy a
tapintócsúcs függőlegesen álljon.
4. Az etalont úgy helyezze el, hogy a teljes
tapintási szakasz a meghatározott érdes-
ségű mezőbe essen
(lásd a 3. ábrát)
.
A tapintási szakasz hossza a né-
vértéktől függően automatikusan
meghatározásra kerül a DIN EN
ISO 4288, ill. ASME B46.1 sze-
rint (lásd a "MarSurf. Surface
Parameters" kártyát). Ehhez hoz-
záadódik a rá- és lefutás fele.
5. Állítsa be a magasságot
(7)
MarSurf PS 10-en
a megfelelő magasságra:
−
PHT 6-350 szabványos tapintónál
értékre,
−
egyéb tapintóknál szükség szerint.
A tapintót az etalonnal párhuzamosan kell
beállítani.
6. Alapnézetben érintse meg a
gombot
(vagy érintse meg a menüben a
Bemérés
pontot).
7. Válassza ki a bemérési eljárást.
A szállított etalon alkalmazása esetén min-
dig az "Rz bemérés"-t válassza ki.
8. Adja meg az "Névérték" mezőben az eta-
lon névértékét.
9. Érintse meg a
Bemérés indítása
gombot.
A három mérés automatikusan végrehaj-
tásra kerül.
10. A 3. mérés után a három mért értékből (
Rz
,
Ra
vagy
RSm
) kerül számításra a korrekciós
érték.
i
3
Első lépések
Az alábbi lépések végrehajtása után indíthatók
a mérések:
−
A szállítási biztosítás eltávolítása
−
Az előtolókészüléket helyezze be a MarSurf
PS 10 készülékbe (lásd
4. fejezetet)
−
Mérési feltételek beállítása
−
Tapintó bemérése
A szállítási biztosítás eltávolítása
A MarSurf PS 10 üzembe vétele előtt
távolítsa el a piros szállítási biztosítást
(lásd a 3763316 tájékoztató lapot)!
A szállítási biztosítást feltétlenül őrizze
meg!
A készülék esetleges visszaszállítása
esetén a szállítási biztosítást ismét fel
kell helyezni!
MarSurf PS 10 bekapcsolása
1. Nyomja meg a zöld
Start
gombot.
Alapbeállítások végrehajtása
1. A "Gratulálunk" párbeszédablakban:
• Érintse meg a
>
gombot a nyelv (
),
a dátum és a pontos idő egymás utáni
beállításához.
• Válassza ki a "mm" vagy "inch" mér-
tékegységet.
• Érintse meg az
OK
gombot.
Megjelenik a menü. Az
OK
gomb is-
mételt érintése megjeleníti az alapné-
zetet.
Mérési feltételek beállítása
1. Alapnézetben érintse meg a
gombot
(vagy érintse meg a menüben a
Mérési
feltételek
pontot).
2. Ismét érintse meg a
gombot és állítsa
be a kívánt mérési feltételeket.
A mérési feltételek részleteit lásd az 5. fe-
jezetben.
3. Érintse meg az
OK
gombot. Ismét érintse
meg az
OK
gombot.
i
Summary of Contents for MarSurf PS 10
