18
Mahr GmbH, MarSurf PS 10
6.1
Integriertes Normal überprüfen
Um den
Rz
-Wert des integrierten Normals zu er-
mitteln:
1. Ein geeignetes Rauheitsmessgerät
9
so po-
si tionieren, dass der Taster auf dem Normal
aufliegt und eine Taststrecke von 5,6 mm
gemessen werden kann
(s. Abb. 3)
.
2. Am Messgerät die Taststrecke
Lt
= 5,6 mm
einstellen.
3. Eine oder mehrere Messungen durchführen
und jeweils den Messwert für
Rz
ablesen.
4. Den Mittelwert aus den gemessenen
Rz
-
Werten bilden.
5. Den ermittelten
Rz
-Wert beim nächsten
Ein messen mit dem MarSurf PS 10 als
Rz
-
Sollwert ein geben.
6.2
Akku wechseln
Die maximale Kapazität des eingebauten Akku-
mu lators kann sich bei langer Nutzung nach und
nach verringern, so dass ggf. der Ersatz des ein-
gebauten Akkus sinnvoll ist.
Der Austausch des Akkus sollte nur von
aus gebildetem Fachpersonal vorgenom-
men werden.
Es darf nur der Li-Ionen-Akku mit 3,7 V /
3150 mAh (3030057) verwen det wer-
den. Anderenfalls be
steht die Ge
fahr,
dass das Gerät zer stört wird.
Um den Akku auszutauschen
(s. Abb. 6 im hin
teren Umschlag)
:
1. Die vier Schrauben
(25)
auf der Unterseite
des MarSurf PS 10 mit einem Kreuzschlitz-
Schrau ben dreher lösen und herausnehmen.
2. Das MarSurf PS 10 auf seine prismatische
Unter seite stellen.
9
z. B. Vor schubgerät MarSurf SD 26 mit Freitaster BFW-250
und Auswertegerät MarSurf M 400 oder MarSurf XR 1
Transport / Versand
Achtung:
Das Vorschubgerät und der Taster kön-
nen beim Transport oder Versand be-
schädigt werden.
Für den Transport oder Versand sind
un
bedingt folgende Anweisungen zu
be achten. Anderenfalls erlischt jeglicher
Garantie an spruch!
Für den innerbetrieblichen Transport im Trage-
etui:
1. Die rote Transportsicherung von unten auf
den Prismenhalter
(9)
aufsetzen (s. Hinweis-
blatt 3763316).
2. Das MarSurf PS 10 ausschalten und im
Trage etui verstauen.
Für den Versand:
1. Das MarSurf PS 10 ausschalten.
2. Das Vorschubgerät aus dem MarSurf PS 10
herausnehmen (s.
in Kap. 4).
3. Die rote Transportsicherung von unten auf
den Prismenhalter
(9)
aufsetzen (s. Hinweis-
blatt 3763316).
4. Das
Vorschubgerät in dem dafür vorgesehe-
nen Fach des zu ge hörigen Versandkartons
ver stauen.
5. Das MarSurf PS 10 (in seinem Trageetui) so-
wie das restliche Zubehör im Versand karton
verpacken.
Summary of Contents for MarSurf PS 10
