7
Mahr GmbH, MarSurf PS 10
Taster kalibreren
1. De normaal
(11)
aan de onderkant van de
MarSurf PS 10 optillen met uw vingernagel
en wegnemen
(zie afb. 1)
.
2. De nominale
Rz
-waarde van de normaal
aflezen.
3. De MarSurf PS 10 op zijn prismatische on-
dergrond zetten, zodat de taststiftpunt ver-
ticaal staat.
4. De normaal zo plaatsen, dat de gehele af-
tastlengte binnen het veld met de gedefini-
eerde ruwheid ligt
(zie afb. 3)
.
De aftastlengte wordt automatisch
bepaald volgens DIN EN ISO 4288
resp. ASME B46.1, afhankelijk van
de nominale waarde (zie het mee-
geleverde vouwblad "MarSurf.
Surface Parameters"). Daarbij wordt
een halve voor- en naloop opgeteld.
5. De hoogteverstelling
(7)
op MarSurf PS 10
op de benodigde hoogte instellen:
−
bij de standaardtaster PHT 6-350 op
,
−
bij andere tasters naar behoefte.
De taster moet parallel aan de normaal lopen.
6. In de basisweergave de toets
aanraken
(of in het menu het item
Kalibreren
).
7. De kalibratieprocedure selecteren.
Als de meegeleverde normaal wordt ge-
bruikt, moet altijd "Kalibreren Rz" worden
geselecteerd.
8. De nominale waarde van de normaal invoe-
ren in het veld "Nominale waarde".
9. De toets
Kalibratie starten
aanraken.
Er worden automatisch drie metingen uit-
gevoerd.
10. Na de derde meting wordt op basis van de
drie gemeten waarden (
Rz
,
Ra
of
RSm
) een
correctiewaarde berekend.
i
3
Eerste stappen
Zodra de volgende stappen zijn uitgevoerd,
kunnen de metingen worden gestart:
−
Transportbescherming verwijderen
−
De aandrijfeenheid in de MarSurf PS 10
plaatsen (zie
in hoofdstuk 4).
−
Meetvoorwaarden instellen
−
Taster kalibreren
Transportbescherming verwijderen
Voordat de MarSurf PS 10 in gebruik
wordt genomen, moet de rode trans-
portbescherming worden verwijderd (zie
instructievel 3763316)!
Bewaar de rode transportbescherming
goed!
Als het apparaat opnieuw moet worden
getransporteerd, dan moet de transport-
bescherming weer worden aangebracht!
MarSurf PS 10 inschakelen
1. De groene
start
-toets indrukken.
Instrumentinstelling uitvoeren
1. In het dialoogvenster "Gefeliciteerd":
•
De toets
>
aanraken, om achtereenvol-
gens de taal (
), datum en tijd in te
stellen.
•
De meeteenheid "mm" of "inch" selec-
teren.
•
OK
aanraken.
Het menu wordt weergegeven. Door
opnieuw
OK
aan te raken verschijnt de
basisweergave.
Meetvoorwaarden instellen
1. In de basisweergave de toets
aanra-
ken (of in het menu het item
Meet voor-
waarden
).
2. De toets
opnieuw aanraken en de ge-
wenste meetvoorwaarden instellen.
Voor bijzonderheden over de meetvoor-
waarden: zie hoofdstuk 5.
3.
OK
aanraken. Nogmaals
OK
aanraken.
i
Summary of Contents for MarSurf PS 10
