9
Mahr GmbH, MarSurf PS 10
To prepare the AC adapter:
1. Select the appropriate mains adapter and
plug it into the AC adapter provided.
2. Plug the USB plug of the USB cable provided
into the AC adapter.
Charging the battery:
1. Connect the micro USB plug of the USB
cable to the USB port
(6)
of the
MarSurf PS 10 and plug the AC adapter into
the mains socket.
The battery symbol
appears in the title
bar during the charging process.
Measurements can be carried out
as soon as the AC adapter has been
con nected.
The battery will be fully charged after approx.
3 hours and the instrument automatically
switches from rapid charge to trickle charge.
2. To display the current battery capacity in %:
Disconnect the MarSurf PS 10 from the AC
adapter and tap
Info
in the menu.
The MarSurf PS 10 can also be charged by
connecting it to a computer via its USB port
(6)
.
If the computer has a special USB charging port,
the charging time also takes approx. 3 hours.
If, however, the computer has a regular USB port,
charging will take approx. 6 to 7 hours.
i
4
Setting up the measuring
station
Mobile measuring station
−
The MarSurf PS 10 can be placed on flat or
cylindrical surfaces as a complete unit
(see
figure 1, above)
.
−
The drive unit can be removed from the
MarSurf PS 10 and placed in its vee-block
holder
(9)
on flat or cylindrical surfaces
(see
figure 1, below)
.
(Please perform
, see below.)
−
The drive unit can be mounted in the
optional hand-held support (6910434) sep-
arately from the evaluation instrument.
(Please perform
,
, see below.)
The hand-held support can be set to differ-
ent heights using the optional, height-
adjustable feet (6850720).
Stationary measuring station
−
The MarSurf PS 10 can be attached to a
MarSurf ST-D, ST-F or ST-G measuring stand
as a complete unit.
An optional holder (6910209) is required for
this.
−
The drive unit can be attached to a MarSurf
ST-D, ST-F or ST-G measuring stand in the
optional hand-held support (6910434).
An optional holder (6851304) is required for
this.
(Please perform
,
, see below.)
−
The cylindrical drive unit can be attached
to a MarStand 815 GN measuring stand or
an existing holding device (clamping shaft
Ø 8 mm
(0.315 in)
).
An optional holder (6910435) is required for
this.
(Please perform
,
, see below.)
Summary of Contents for MarSurf PS 10
