2
Mahr GmbH, MarSurf PS 10
Utilisation conforme à l'usage prévu
L'appareil de mesure de rugosité MarSurf PS 10
doit servir exclusivement à la mesure et à l'analyse
de rugosité.
L'appareil de mesure de rugosité MarSurf PS 10
peut être installé aussi bien à proximité de la ligne
de production que dans des locaux de mesure.
Respecter impérativement les consignes
d'utilisation, de maintenance et d'entre-
tien indiquées dans le présent guide de
l'utilisateur et dans les guides de l'utilisa-
teur des composants du poste de mesure.
Toute utilisation autre que l'utilisation
définie au point « Utilisation conforme
à l'usage prévu » et toute utilisation
outrepassant l'utilisation conforme sont
réputées non conformes et causent l'an-
nulation de la garantie et l'exclusion de la
responsabilité du fabricant.
Élimination
Les appareils électroniques et leurs accessoires, ainsi que les piles ou les
batteries usagées, ne doivent pas être jetés dans les ordures ménagères.
En effet, ils sont fabriqués à partir de matériaux de grande valeur qui
peuvent être recyclés et réutilisés. La directive européenne 2002/96/CE
(DEEE) impose que les déchets d'équipements électriques et électroniques
soient traités séparément des déchets urbains non triés pour pouvoir être
réutilisés. Le symbole de la poubelle barrée signale l'obligation de tri sélectif.
Pb, Cd et Hg désignent des composants situés au-dessus des valeurs
légales.
La société Mahr GmbH procède à la reprise et à l'élimination de ses produits
électriques et électroniques dans le respect de la législation. Contacter
notre service d'assistance sur place ou s'adresser à
Mahr GmbH
Carl-Mahr-Straße 1
D-37073 Göttingen
République Fédérale d'Allemagne
Téléphone :
+49-551-70730
Fax :
+49-551-71021
Courriel :
info@mahr.de
Site web :
www.mahr.de
La société Mahr GmbH est enregistrée en Allemagne avec le numéro
d'immatriculation DEEE DE 56624193 auprès de la fondation Elektro-
Altgeräte-Register (EAR).
Erreurs d'utilisation raisonnablement pré-
visibles
Tous les travaux à réaliser ne doivent être
effectués que par un personnel spécialisé
suffisamment formé et instruit, sur instruc-
tion de la société d'exploitation.
Tous les travaux à réaliser ne doivent être
effectués qu'avec les équipements de pro-
tection individuelle nécessaires à cet effet.
Les travaux sur les pièces conductrices
ne doivent être réalisés que lorsque l'ap-
pareil a été isolé du réseau et que les
éventuelles tensions résiduelles ont été
entièrement déchargées.
Les dispositifs de protection ne doivent
pas être démontés ni pontés.
Utiliser uniquement des palpeurs et ac-
cessoires du fabricant d'origine.
Summary of Contents for MarSurf PS 10
