7
Mahr GmbH, MarSurf PS 10
Calibrer palpeur
1. Soulever l'étalon
(11)
sur le fond du MarSurf
PS 10 avec un ongle et le sortir en faisant
levier
(voir fig. 1)
.
2. Lire la valeur nominale
Rz
de l'étalon.
3. Poser le MarSurf PS 10 sur sa base prisma-
tique de façon à ce que la pointe de palpage
soit verticale.
4. Placer l'étalon de façon à ce que toute la
longueur d'exploration soit dans le champ
de rugosité définie
(voir fig. 3)
.
La longueur d'exploration est calcu-
lée automatiquement selon NF EN
ISO 4288 ou ASME B46.1 en fonc-
tion de la valeur nominale (voir le
dépliant fourni « MarSurf. Surface
Parameters »). À cette longueur
s'ajoute une demi-précourse et post-
course.
5. Effectuer le réglage en hauteur
(7)
du MarSurf
PS 10 :
−
pour le palpeur standard PHT 6-350,
régler à ,
−
selon les besoins pour les autres pal-
peurs.
Le palpeur doit être aligné parallèlement à
l'étalon.
6. Dans la vue de base, toucher le bouton
(ou toucher l'option
Calibrage
dans le
menu).
7. Sélectionner le procédé de calibrage.
En cas d'utilisation de l'étalon fourni, toujours
sélectionner « Calibrer Rz ».
8. Saisir la valeur nominale de l'étalon dans le
champ « Valeur de consigne ».
9. Toucher le bouton
Démarrer calibrage
.
Trois mesures sont effectuées automatique-
ment.
10. Après la 3e mesure, une valeur de correction
est calculée à partir des trois valeurs mesurées
(
Rz
,
Ra
ou
RSm
).
i
3
Premiers pas
Il est possible de commencer les mesures dès que
les opérations suivantes sont terminées :
−
Dépose de la fixation de transport
−
Introduction de l'unité d'avance dans le
MarSurf PS 10 (voir
au chap. 4).
−
Réglage des conditions de mesure
−
Calibrage du palpeur
Dépose de la fixation de transport
Avant de mettre le MarSurf PS 10 en
service, déposer la fixation de transport
rouge (voir la notice 3763316) !
Conserver impérativement la fixation de
transport !
En cas de retour de l'appareil, la fixation
de transport doit être reposée.
Mise en marche du MarSurf PS 10
1. Appuyer sur la touche verte
Start
.
Procéder aux réglages de base
1. Dans la boîte de dialogue « Félicitation » :
•
Toucher le bouton
>
pour régler la
langue (
), la date et l'heure.
•
Sélectionner l'unité de mesure « mm »
ou « inch ».
•
Toucher
OK
.
Le menu s'affiche. Pour afficher la vue
de base, toucher à nouveau
OK
.
Réglage des conditions de mesure
1. Dans la vue de base, toucher le bouton
(ou toucher l'option
Conditions de mesure
dans le menu).
2. Toucher à nouveau le bouton
et régler
les conditions de mesure souhaitées.
Pour les détails des conditions de mesure,
voir le chap. 5.
3. Toucher
OK
. Toucher à nouveau
OK
.
i
Summary of Contents for MarSurf PS 10
