19
Mahr GmbH, MarSurf PS 10
6.3
Installation d'une mise à jour
du logiciel
Lors de la mise à jour du logiciel, tous
les réglages
et tous les profils, résultats
et rapports enregistrés dans la mémoire
sont conservés.
Exception :
En cas de mise à jour du logiciel de la
version v1.00-12 (ou inférieure) à la ver-
sion v1.00-14 (ou supérieure), suivre les
étapes suivantes :
•
Avant de démarrer la mise à jour,
sauvegarder si nécessaire les don-
nées de la mémoire interne, c'est-à-
dire les données de
\\MarSurfPS10 \Export
\Profiles
\Records
\usersettings
•
Après la mise à jour, le palpeur du
MarSurf PS 10 doit être recalibré (voir
chap. 3).
N'effectuer la mise à jour du logiciel que
si la batterie est entièrement chargée ou
si le MarSurf PS 10 est branché au secteur
par le bloc d'alimentation secteur !
Pour installer une nouvelle version du logiciel :
1. Éteindre le MarSurf PS 10.
2. Introduire la carte MicroSD contenant la mise
à jour dans le slot
(5)
.
3. Mettre le MarSurf PS 10 en marche.
La nouvelle version du logiciel est automati-
quement installée, un avertissement s'affiche.
4. Extraire la carte MicroSD du slot
(5)
.
i
3. Ouvrir prudemment la partie supérieure
(26)
du MarSurf PS 10 à 90° vers la gauche
(comme la couverture d'un livre).
4. Débrancher avec précaution les fiches
(27)
et
(28)
des connecteurs
(27a)
et
(28a)
de la
carte.
5. Desserrer les trois vis du couvercle de la bat-
terie
(30)
.
6. Sortir la batterie
(29)
.
7. Introduire la nouvelle batterie (3030057) avec
les inscriptions vers le haut.
8. Poser le couvercle de la batterie
(30)
sur la
batterie (avec l'inscription « Top » vers le haut)
et visser les trois vis au couple de 0,4 Nm.
9. Brancher les fiches
(27)
et
(28)
sur les connec-
teurs
(27a)
et
(28a)
de la carte.
10. Remettre en place avec précaution la partie
supérieure du MarSurf PS 10.
Les quatre vis sont des vis autota-
raudeuses. Le boîtier risque d'être
endommagé si un couple trop élevé
est appliqué lors du serrage !
11. Reposer les quatre vis
(25)
et les serrer au
couple max. d'1 Nm.
12. Mettre le MarSurf PS 10 en marche et vérifier
qu'il fonctionne correctement.
13. Vérifier les réglages du MarSurf PS 10.
14. Charger entièrement la batterie du MarSurf
PS 10.
Summary of Contents for MarSurf PS 10
